Operation Via A Light Controller; Cleaning Of The Unit; Specifications - IMG STAGE LINE LSX-80R Bedienungsanleitung

the sound picked up by the microphone, the blue LED
GB
BEAT (4) shortly lights up.
Notes
1. When changing the volume on the music system, also
the microphone sensitivity must be adapted with the
rotary control accordingly.
2. During music breaks or if the volume of the music is too
low, the laser beam will be turned off.
5.1 Interconnecting several lasers
It is possible to interconnect several lasers (LSX-40G,
LSX-80R, LSX-120RG, also mixed). The master unit
thus controls the slave units in sync so that all units cre-
ate the same laser pattern and change the pattern in the
same moment.
1) Connect the DMX OUTPUT (7) of the master unit via
a 3-pole XLR cable (e. g. series MEC-... or MECN-...
from the product range of "img Stage Line") to the
DMX INPUT (8) of the first slave unit.
2) Connect the DMX OUTPUT of the first slave unit to
the DMX INPUT of the second slave unit etc. until all
units are connected in a chain.
3) Set the slave units to the slave mode: Press the button
FUNC (5) so many times until the display (6) shows
. Memorize the mode with the button ENTER.

6 Operation via a light controller

For operation via a light controller with DMX512 protocol
(e. g. DMX-1440 or DMX-510USB from "img Stage
Line") the models LSX-40G and LSX-80R are equipped
with 8 DMX control channels and the model LSX-120RG
with 9 channels. The functions of the channels and the
DMX values can be found in chapter 8.1 on page 11.
6.1 DMX connection
For DMX connection, 3-pole XLR connections with the
following contact configuration are available:
pin 1 = ground, 2 = DMX-, 3 = DMX+
For connection special cables for high data flow should be
used. Microphone cables with a standard screening and a
minimum cross section of 2 × 0,22 mm
ity as low as possible can only be recommended for a total
cable length of up to 100 m. For cable lengths exceeding
150 m it is recommended to insert a DMX level matching
amplifier (e. g. SR-103DMX by "img Stage Line").
1) Connect the DMX INPUT (8) to the DMX output of the
light controller.
2) Connect the DMX OUTPUT (7) to the DMX input of
the following light effect unit; connect its output again
to the input of the following unit etc. until all light effect
units have been connected in a chain.
3) Terminate the DMX output of the last DMX unit in the
chain with a 120 Ω resistor (> 0.3 W): Solder the resis-
tor to the pins 2 and 3 of an XLR plug and connect the
plug to the DMX output or use a corresponding termi-
nating plug (e. g. DLT-123 by "img Stage Line").
* for model LSX-120RG
10
6.2 Adjusting the start address
To be able to operate the laser with a light controller, the
DMX start address for the first DMX channel must be
adjusted. If e. g. on the controller the address 17 is pro-
vided for adjusting the operating mode, adjust the start
address 17 on the laser. The DMX channels 2 to 8 (2 to 9)*
are then automatically assigned to the addresses follow-
ing it [in this example 18 to 24 (18 to 25)*]. As the next
possible start address for the following DMX-controlled
unit the address 25 (26)* could be used for this example.
1) Press the button FUNC (5) so many times until the
2) Adjust the desired address with the button UP or
3) Memorize the address with the button ENTER. The

7 Cleaning of the Unit

The outlet pane of the laser beam should be cleaned at
regular intervals, depending on impurities caused by
dust, smoke, or other particles. Only in this case the
laser beam can be radiated at maximum brightness.
Prior to cleaning, disconnect the mains plug from
the mains socket. Only use a soft, clean cloth and a
detergent for glass. Then carefully wipe the pane dry.
soft, clean cloth. Never use any fluid, it could penetrate
the unit and cause damage.

8 Specifications

Laser class: . . . . . . . . . 3b
Laser type: . . . . . . . . . . laser diode, CW (continuous
2 and with a capac-
Colour / wavelength / power
Power supply: . . . . . . . 230 V~ / 50 Hz
Max. power consumption
Ambient temperature: . 10 – 40 °C
Dimensions: . . . . . . . . . 252 × 140 × 200 mm
Weight
display (6) shows a number between 1 and 511 (also
see fig. 5). The number indicates the DMX start
address.
DOWN.
display confirms the storage by the indication
lighting up three times.
After adjusting the start address, this is perma-
nently shown on the display and the laser can be
operated via the DMX controller.
For cleaning the other parts of the housing only use a
wave)
LSX-40G: . . . . . . . . green / 532 nm / 30 – 40 mW
LSX-80R: . . . . . . . . . red /
LSX-120RG: . . . . . . green / 532 nm / 30 – 40 mW and
red /
LSX-40G, LSX-80R: 15 VA
LSX-120RG: . . . . . . 30 VA
LSX-40G: . . . . . . . . 1.9 kg
LSX-80R: . . . . . . . . . 1.7 kg
LSX-120RG: . . . . . . 2.2 kg
650 nm / 70 – 80 mW
650 nm / 70 – 80 mW