Audio Pro LIVING LV33 Bedienungsanleitung Seite 5

LEFT, MONO AND RIGHT
On the rear of LV33 is a switch for left, mono and right. Normally two
LV33 speakers are used in one room for stereo sound. Set one speaker to
RIGHT, the other to LEFT.
NOTE: Only speaker set to RIGHT can receive commands from remote.
MONO is used if you have only one LV33 in one room, and the other in
another room. Or very large room, or reception hall where all speakers
play in mono. Note that the speakers will reproduce sound in mono, not
stereo.
MONO MASTER
If you have your LV33 speakers set to MONO, you will need to make one
of them MONO MASTER to be able receive commands from the remote.
Setting one speaker as MONO MASTER:
1. Aim remote at desired speakers, push Zone INFO button for 5 seconds.
2. Display will show "111". Now the speaker is mono master speaker.
To change back to slave mode mono speaker, push Zone info button on
remote again for 5 seconds, display shows "000".
MORE OR LESS BASS (ROOM ADAPTATION)
When placing LV33 in your home, you may experience too much or too
little bass, depending on where you place the speakers. To solve this,
LV33 has built in room adaptation (+10/-10 dB bass equalizer). By adjust-
ing bass levels, you can find a good bass balance that suits your room.
Generally, placing LV33 in a corner will reproduce more bass, placing
LV33 in the middle of your room less bass. With room adaptation you can
place LV33 anywhere you like, and then adjust bass levels to your liking.
ADJUST BASS EQ:
1. Use buttons on speaker (not remote)
2. Press button "House Code" and hold it pressed
3. While holding "House Code" button pressed, adjust bass EQ with
VOL + and –. Press + to increase bass, – to decrease bass
Display will show your settings: -10, -9, -8 ... 0 ... 8, 9, 10
RESET SPEAKER
Returning to factory settings (volume 17, bass EQ 0):
Turn off speakers with remote. Turn on again and press MUTE on remote
while LED flashes. Push Mute once more. Now speaker pair (or all speak-
ers in same Zone) are in default setting.
8
OPERATIONS WITH LV-HUB
With the Living LV-HUB (sold separately) you get convenient features such as listening to different
sources in different rooms. You can also change sources connected to LV-HUB on the speakers with
the remote.
House Code 1
Zone A
Room 1: LV33 by TV
Audio from TV
Connected sources:
TV
Apple TV ®
Turntable
Computer
1. Set all speakers and LV-HUB to same House Code.
2. Set speakers in each room to Zone A, B or C.
3. Pair LV-HUB with all speakers (See Pairing in specific speaker manual.)
4. Connect up to 4 sources to LV-HUB.
Now you can play from any source connected to LV-HUB to any speakers in different zones.
Changing source: use remote aimed to speaker to change source. You can change source in each
room on the speakers with the remote, and listen to different sources at the same time in different
room. Example:
- Watch movie with wireless sound in Room 1.
- Listen to music on computer in Room 2.
- Listen to music via AirPlay® (via Apple TV®) in Room 3.
Speaker display will show this for sources: USB–LI–OP1–OP2
Note:
1. When in paired mode, the LV-HUB can be hidden away. No commands from remote works on the LV-HUB. All commands
are done on the speakers.
2. Choosing source will follow the ZONE, all speakers set to same Zone will play same source.
3. If you add a TXD200 transmitter, and this is paired, you can also change House Code on speakers to choose different
transmitter (Example:HC1 on LV-HUB and HC2 on TXD200.)
House Code 1 House Code 1
Zone B Zone C
Room 2: LV33 Room 3: LV33
Audio from computer Audio from Apple TV
Transmitting on House Code 1
(AirPlay )
® ®
9