TESY CN03 050 EIS Bedienungsanleitung Seite 5

When the heater is operating the red diode light is
constantly on!
Temperature adjustment.
By pushing any of the buttons
"Temperature adjustment" mode. The display starts
blinking and then it shows the temperature set so far. If
you then press the buttons you can change temperature
settings in the desired direction. If up to 5 sec. you do
not push any button, the new settings are saved and
the heater goes automatically into "Heating" mode. If
any of or buttons gets pressed longer than 0.7
sec., the temperature settings will start automatically to
increase or decrease at a rate of 4 units per second. The
range of available temperature settings is from 12 to 30
degrees.
„Delayed start" of the panel heater.
When the panel heater is in "Turned-off" mode by
pushing the "Timer" button you can enter the time,
then it will automatically go into "Heating" mode. This
mode is indicated by a blinking yellow diode light
and turned-off red diode light. The digital display will
show alternately: ambient temperature readings when
"Temperature LED" is on, and remaining time in hours
until turning-on "Heating" mode when "Time LED" is
on. Immediately after enabling this mode, the yellow
diode light goes on, and the digital display starts
blinking as it shows the already set time in hours until
the panel heater gets turned-on. Initially a setting
of 12 hours is set by default and by pushing
buttons you can change the time settings in the
desired direction. If any of
and held for more than 0.7 seconds, the time settings
start automatically to increase or decrease at a rate of
4 units per second. If for up to 5 seconds you do not
push any button or by pushing "Timer" button, the
time regulator will go into "Delayed start" mode. If you
enter time – 00, this mode will not be implemented.
If "Delayed start" mode is already enabled and you
push the "Timer" button again, you can change the
remaining time in both possible directions. After
adjusting the time, the appliance goes into "Delayed
start" mode and the display will show both the
temperature and the remaining hours until initiation
of "Heating" mode. You can exit this mode by pushing
the "On/Off" button. Then panel heater will go into
"Heating" mode.
Deactivation of "Heating" mode
You can exit "Heating" mode by pushing the "On/Off"
button. Then the heater turns off, if it has been turned
on before that and the red diode light goes off. The
display will continue showing the room temperature.
English
or , you enter
or
or buttons is pressed
„Delayed stop" for turning-off the panel heater.
When the panel heater is in "Heating" mode, by
pushing the "Timer" button it is allowed to enter
time, then the appliance will automatically turn off.
This mode is indicated by a blinking yellow and
illuminated red diode light. The digital display will
alternately show: ambient temperature readings when
the "Temperature LED" is on, and remaining time in
hours until activation of "Heating mode" when the
"Time LED" is on. Immediately after activation of this
mode yellow diode light goes on and digital display
starts blinking and showing the remaining time in
hours until turning-off of the panel heater. Initially a
value of 12 hours is set by default and by pushing
or buttons you can change the time settings in the
desired direction. If any of
and held for more than 0.7 sec., the time settings will
automatically start increasing or decreasing at a rate
of 4 units per second. If for up to 5 sec. you do not
push any button or you push the "Timer" button, the
control unit will go into "Delayed stop" mode. If you
enter time – 00, the mode will not be implemented
and the panel heater will remain in "Heating" mode.
If "Delayed stop" mode is already enabled and you
push the "Timer" button again, you can change the
remaining time in both possible directions. After
adjusting the time settings the appliance goes into
"Delayed stop" mode and the display will show both
the temperature and the hours remaining until
turning-off the panel heater. You can exit this mode by
pushing the "On/Off" button, which will turn off the
panel heater at once.
„Sleep" mode
This mode gives you another possibility for economy
of electricity by automatically and gradually, for 2
hours, decreasing the already set temperature by 3
degrees. In that way after you are already in bed and
well tucked, the panel heater will decrease the set
temperature by itself without leaving you in the cold.
This mode is activated when the panel heater is in
"Heating" mode by pushing and holding for more than
2 seconds the "Timer" button. This mode is indicated by
constantly illuminated yellow diode light and blinking
or illuminated red diode light. After enabling this mode,
the panel heater will continue displaying the measured
room temperature. "Sleep" mode can be stopped
by pushing again the "Delayed start" button, which
will turn the panel heater into "Heating" mode with
the temperature settings which have been adjusted
beforehand. Another way to disable this mode is by
pushing the "On/Off" button which will turn the panel
heater off.
or buttons is pressed
Operation and Storage Manual
EN
5