Operating Elements And Connections; Safety Notes - IMG STAGE LINE STROBE-4C Bedienungsanleitung

Please unfold page 3. Then you will always see the
operating elements and connections described.

1 Operating Elements and Connections

1 Display: to indicate the number of the chase pro-
gramme selected
2 Button MODE for selection between the two oper -
ating modes; the corresponding LED above the
button will show the operating mode selected
SOUND mode
flashing of stroboscopes by music control
AUTO mode
flashing of stroboscopes in accordance with the
chase programme adjusted
3 Buttons CHASE for selecting one of the 10 chase
programmes
upward selection of programmes
downward selection of programmes
4 Control SPEED for adjusting the flash rate in the
AUTO mode
5 Control DIMMER for adjusting the flash intensity
between 20 % and 100 %
(for DMX-controlled stroboscopes only)
6 Button BLACKOUT for activating the Blackout
function (sleep mode: lamp off) for all strobos copes,
the LED above the button is on; for deactivating the
Blackout function, press the button once again
7 Button FULL ON: while the button is kept pressed,
all stroboscopes will flash rapidly at the same time
8 Button SINGLE FLASH: when the button is pressed
with the Blackout function activated (LED above the
button BLACKOUT is on) all stroboscopes will flash
just once
9 POWER switch
10 Power supply jack (9 V /500 mA min.) for connect -
ing the plug-in power supply unit supplied
11 Jacks ANALOG OUTPUT CH 1 – CH 4 (control volt -
age +5 V ) for connecting up to four strobo scopes
with analog control via cables with 6.3 mm mono
plugs
12 3-pole XLR jack DMX OUTPUT (1 = ground,
2 = DMX-, 3 = DMX+) for connecting the DMX
signal input of the first DMX-controlled stroboscope
in the chain

2 Safety Notes

The units (controller and power supply unit) corre -
spond to all required directives of the EU and are
therefore marked with
WARNING The plug-in power supply unit is sup-
plied with hazardous mains voltage
(230 V~). Never make any modifica tion
on the power supply unit, otherwise you
will risk an electric shock!
Please observe the following items in any case:
G
The units are suitable for indoor use only. Protect
them against dripping water and splash water, high
air humidity, and heat (admissible ambient tempera-
ture range 0 – 40 °C).
G
Do not operate the controller and immediately dis-
connect the power supply unit from the socket
1. in case of visible damage to one of the units,
2. if a defect might have occurred after a unit was
dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the units must be repaired by skilled per-
sonnel.
G
For cleaning only use a dry, soft cloth, never use
water or chemicals.
G
No guarantee claims for the units and no liability for
any resulting personal damage or material damage
will be accepted if the units are used for other pur-
poses than originally intended, if they are not cor-
rectly connected, operated, or not repaired in an
expert way.
If the units are to be put out of operation de-
finitively, take them to a local recycling plant
for a disposal which is not harmful to the envi-
ronment.
3 Applications
The STROBE-4C is a user-friendly miniature controller
which allows simultaneous operation of four stro bo -
scopes with analog control (e. g. STROBE-75*) and
four 2-channel DMX stroboscopes (e. g. STROBE-
1500DX*). The controller offers two operating modes:
a music mode in which the flashing of the strobo -
scopes is controlled by an internal microphone and an
automatic mode in which 10 different chase pro -
grammes (flash patterns) are adjustable. Two controls
are used to modify the flash rate and the flash intensity
(flash intensity available with DMX control only). In
addition, the functions "Blackout", "Full On", and
"Single Flash" may be activated.
* from the range of "img Stage Line"
.
GB
7