Operating Elements And Connections; Safety Notes - Monacor PT-24 Bedienungsanleitung

Please unfold page 5. Then you can always see
GB
the operating elements and connections de-
scribed.

1 Operating Elements and Connections

1.1 Front Side
1 LED indicator lights up if the camera is panned
automatically or manually
2 Switch to activate the automatic panning function
upper position: automatic panning
mean and lower position: manual panning
3 Momentary push-button for panning to the l. h.
and r. h. sides
4 Momentary push-button for upward and down-
ward tilting
5 Momentary push-button for zoom control of a
motor zoom lens (only with model PTL-124)
6 Momentary push-button for focus control of a
motor zoom lens (only with model PTL-124)
7 On/off switch
1.2 Rear Side
8 Mains cable for power supply 230 V~/50 Hz
9 Connection for the panning/tilting device of the
camera
Connections (from left to right):
1 Ground (common)
2 Panning to the r. h. side*
3 Panning to the l. h. side*
4 Automatic panning*
5 Downward tilting*
6 Upward tilting*
*when activated, a voltage of 24 V~ is present
10 Power supply connection for the camera and with
model PTL-124 additionally for a motor zoom lens
Connections (from left to right):
1 +12 V , max. 500 mA power supply for the
1 camera
2 Ground for the camera power supply
3 Motor zoom*
4 Motor zoom*
5 Motor focus*
6 Motor focus*
*Connections 3 – 6 only with model PTL-124;
when activated, a voltage of 12 V
in case of wrong turning direction of the motor zoom or
focus, change the connections 3 + 4 or 5 + 6

2 Safety Notes

This device is in accordance with the directive for
electromagnetic compatibility 89/336/EEC as well as
the directive for low voltage 73/23/EEC.
The device is supplied with dangerous mains volt-
age (230 V~). Therefore, do not open the device.
Inadequate handling may cause an electric shock.
Leave servicing to authorized, skilled personal only.
In addition, any kind of guarantee expires when
opening the device.
Please observe the following items in any case:
8
The device is suitable for indoor use only. Protect it
from humidity and heat (admissible ambient tem-
perature 0–40 °C).
Do not operate the unit or immediately disconnect
the plug from the mains socket
1. if there is visible damage to the unit or to the
2. if a defect might have occurred after the unit was
3. if malfunctions occur.
Have the device repaired in a technical workshop.
A damaged mains cable may only be replaced by
the manufacturer or an authorized technical work-
shop.
Do not pull the mains plug out of the socket by the
mains cable.
Only use a dry, soft cloth for cleaning, by no means
chemicals or water.
If the device is used for other purposes than orig-
inally intended, if it is wrongly operated or not re-
paired by an expert, no liability can be assumed.
Should the device definitively be put out of opera-
tion, it has to be disposed of in a local recycling
plant.
Important for U. K. Customers!
The wires in this mains lead are coloured in accord-
ance with the following code:
green/yellow = earth
blue = neutral
brown = live
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug, pro-
ceed as follows:
1. The wire which is coloured green and yellow
2. The wire which is coloured blue must be con-
3. The wire which is coloured brown must be con-
is present;
Warning - This appliance must be earthed.
3 Application
Purpose of the devices PT-24 and PTL-124 is to con-
trol in video monitoring systems the camera panning /
tilting devices equipped with 24 V a.c. motors (e. g.
VP-55 and VPT-50 by MONACOR). In addition, a
motor zoom lens can be controlled with model
PTL-124 (e. g. VMZL-8014A by MONACOR). Further-
more, the devices supply a monitoring camera with a
d.c. voltage of 12 V (max. 500 mA).
mains cable,
dropped or suffered a similar accident,
must be connected to the terminal in the plug
which is marked with the letter E or by the earth
symbol , or coloured green or green and yel-
low.
nected to the terminal which is marked with the
letter N or coloured black.
nected to the terminal which is marked with the
letter L or coloured red.