Electrical Connection - STEINEL CAM light Handbuch

Product components ( Fig� 3�3 )
A Camera light
Lock
B
C Connecting terminal
D Wall mount
E Sensor unit
F Camera
Reset button
G
H Status LED
I Slot for memory card
4� Electrical connection
• Switch OFF power supply ( Fig� 4�1 )
Wiring diagram ( Fig� 4�1 )
The supply lead consist of three wires:
= phase conductor ( usually black,
L
brown or grey )
N = Neutral conductor ( usually blue )
= protective-earth conductor
( green/yellow )
If you are in any doubt, identify the
conductors using a voltage tester; then
disconnect from the power supply
again. Connect phase, neutral and pro-
tective-earth conductor to the terminal.
Important: Incorrectly wired connections
will produce a short circuit later on in the
product or your fuse box. In this case,
you must identify the individual conduc-
tors once again and reconnect them. A
mains power switch for turning the unit
ON and OFF may of course be installed
in the mains supply lead.
The light source of this luminaire cannot
be changed. If the light source needs
to be replaced ( e.g. at the end of its
service life ), the complete luminaire
must be replaced.
Connection to a dimmer will result in
damage to the camera light.
5� Mounting
• Check all components for damage.
• Do not use the product if it is dam-
aged.
• When installing the camera light,
make sure the installation site is not
exposed to vibration.
• Select an appropriate mounting
location, taking the reach and motion
detection into consideration. ( Fig� 5�1 )
• Select an appropriate mounting
location, taking the WLAN speed into
consideration. A minimum of 2 Mbps
must be available for operation.
Mounting procedure
• Undo retaining screw, detach camera
light from wall mount. To do this,
press lock ( Fig� 5�2 )
• Mark drill holes ( Fig� 5�3 )
• Drill holes and insert wall plugs
( Fig� 5�4 )
• Screw down wall mount ( Fig� 5�5 )
• Connect conductors ( Fig� 5�6 )
• Fit camera light on wall mount and
tighten retaining screw ( Fig� 5�7 )
• Switch ON power supply ( Fig� 5�7 )
• Make settings ➜ "6� Function"
The camera can be aligned by hand.
( Fig� 5�8 )
6� Function
Factory settings
Twilight level: 10,000 lux
Time setting: 1 minute
Night light: 40%
14
Android
iOS
Note:
The camera light needs a stable Wi-Fi
connection. The smartphone or tablet
used must have access to the
Internet and be connected to the same
Wi-Fi network as the camera light for the
installation process.
Installation
• Download app.
• The camera light is ready for configu-
ration as soon as the power supply is
switched ON. A signal sounds every
4 seconds during configuration.
• The signal sounds once a second
while the camera light is being
connected to the smartphone or
tablet.
• Now enter the network name and
password of the Wi-Fi router into
your app.
Camera function
When the camera is connected to a
smartphone or tablet, it is disabled for
external access. A QR code is generat-
ed on the smartphone or tablet which
can be read by another smartphone or
tablet.
• Once the sensor has triggered, you
will receive a push notification via
the app.
• Open the app. You can now use the
image display and intercom system.
The camera films a sequence when the
sensor has been triggered. The filmed
sequence is saved on the memory
card and can be retrieved at any time.
The recorded data is only saved on the
camera light's memory card.
Note:
You will find further information on the
functions and setting options in the app.
Twilight setting
The chosen response threshold can be
infinitely varied from 10 to 10,000 lux.
Time setting
The time you wish light to stay ON
for can be set to 1 minute, 3 minutes,
10 minutes or 15 minutes. Any move-
ment detected before this time elapses
will restart the timer.
Night light
The night-light function provides illumi-
nation at 0% to 40% light output when
ambient light falls below the light-level
setting.
15