Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Key functions on the IR remote control
„POWER" key
Use it to turn the converter on or off.
„VIDEO STANDARD" key
Via this button you can switch to the different PAL/NTSC
modes. For Germany the correct setting is „PAL".
„Menu" key
With each push of a button it is switched between the fol-
lowing functions (adjustment in each case with the arrow
keys):
„FINE TUNE"
„H/SIZE"
„V/SIZE"
„BRIGHTNESS" Brightness
„CONTRAST"
„HUE"
„SATURATION" Colour saturation
„FLICKER"
„OSD COLOR"
„SAVE"
„ZOOM" key
Zooms the picture; move the picture detail with the „UP",
„DOWN", „LEFT" and „RIGHT" keys or with the arrow keys
of the remote control; press the key again to end the zoom
mode
Control keys
The control keys „UP" (1), „DOWN" (2), „LEFT" (3) and
„RIGHT" (4) are used for adjustment, depending on the
selected function, e.g. picture width, picture height, etc.
„FREEZE" key
This key activates or deactivates the freeze image func-
tion. „FREEZE ON" ( freeze image function activated) or
„FREEZE OFF" (freeze image function deactivated)
appears briefly on the screen.
„RESET" key
This key resets the picture settings (e.g. moving with the
arrow keys) to the default setting.
The „
", „
", „
", „
" keys The arrow keys have the same function as the control keys
„UP" (1), „DOWN" (2), „LEFT" (3) and „RIGHT" (4) on the
converter.
They are used to change a setting, e.g. the image width,
height, etc.
Tips & Notes
• Because of its functionnal principle, the video image that the converter delivers to its outputs,
only has a resolution of about 720*576 pixels. This is why higher resolutions of the graphics
card's VGA picture (e.g. 1024*768) are only displayed quite out of focus because the picture
has to be made smaller. This is why small print cannot be read properly on the television.
You should therefore use, for e.g. presentations, either a larger font size or a smaller VGA res-
olution (e.g. 800x600 instead of 1024x768).
• If the power supply is via an USB port, attention needs to be paid to the fact that the USB port
can supply a current of 500mA (so called „high-power USB port"). Use a USB port directly on
the motherboard (on the back of the PC) or a USB port of a USB hub with own power supply.
• Pay attention to the correct connection of the Y-VGA connecting cable. On each of the plugs
the respective labelling can be found.
• For notebooks the VGA output may have to be activated first. This is usually possible via a spe-
cial shortcut.
• For higher resolutions and refresh rates the VGA monitor image may get worse (shadows on
vertical lines or similar). If this is the case, reduce the resolution or the refresh rate (eg 800*600
in 75Hz instead of 1280*1024 in 60Hz).
Fine-tuning of the video image
Picture width
Picture height
Contrast
Colour setting, only for NTSC
Flicker reduction
Colour for OSD menu
Saving all settings: Press the key „
„SAVE ON" appears. Now wait for a few
seconds until the OSD disappears again,
all settings are now saved automatically.
Alternatively, you can briefly press the
„SAVE" key on the converter to save all
settings.
Disposal
a) General
Please dispose of the product, when it is no longer of use, according to the current
statutory requirements.
b) Disposal of batteries and rechargeable batteries
The end user is legally obliged (Battery Regulation) to return used batteries and rechargeable
batteries. Do not dispose of used batteries via the domestic waste!
Batteries/rechargeable batteries containing harmful substances are marked with the
following symbols, which point out that disposal in the domestic waste is prohibited.
The symbols for the relevant heavy metals are: Cd=cadmium, Hg=mercury, Pb=lead
(designation can be found on battery/rechargeable battery under the trash icons on
the bottom left).
You can dispose of your used batteries/rechargeable batteries free of charge at your
community's collection point or any place where batteries/rechargeable batteries are
sold!
You therefore fulfil your statutory obligations and contribute to the protection of the environment.
",
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data pro-
cessing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2009 by Conrad Electronic SE.
Werbung
Inhaltsverzeichnis
