Renkforce 1391579 Bedienungsanleitung Seite 5

b) Setting the time
• Repeatedly press the "FUNC" button briefly until "CANCEL" appears in the display.
• Hold the "FUNC" button pressed (approx. 3 seconds) until the weekday flashes on
the top in the display (above the displayed time).
• Set the weekday or the period using the "+/ON" or "-/OFF" buttons.
"MO" = Monday
"TU" = Tuesday
"WE" = Wednesday
"TH" = Thursday
"FR" = Friday
"SA" = Saturday
"SU" = Sunday
• Briefly press the "FUNC" button to confirm and the hours will flash.
• Set the hours with the "+/ON" or "-/OFF" buttons. For quick adjustment, press and
hold down the corresponding button for longer.
• Briefly press the "FUNC" button to confirm and the minutes will flash.
• Set the hours minutes with the "+/ON" or "-/OFF" buttons. For quick adjustment,
press and hold down the corresponding button for longer.
• Briefly press the "FUNC" button to confirm and to exit the setting mode.
c) Registering a receiver for the temperature controller
The temperature controller can control a receiver of the RS2W radio switch
system (e.g. a radio switch socket that is part of the system). Other receivers
cannot be used.
Follow the operating instructions of the receiver of the RS2W radio switch
system that will be used prior to the registration procedure.
A dimmer of the RS2W radio switch system cannot be used.
During the registration process, maintain a 20 - 30 cm minimum distance
between the temperature controller and the receiver. Failing to do this may
result in a registration failure.
• If the receiver is switched on, switch it off for the moment.
The receiver (e.g. a radio switch socket) must be switched off (LED in the
button is off); otherwise, registration cannot be done.
• Start the registration procedure at the temperature controller.
• Repeatedly press the "FUNC" button briefly until "CANCEL" appears on the left in
the display.
Hold the "+/ON" button pressed for 2 seconds until the two arrows in the "
symbol flash alternately. Then release the button.
The temperature controller is now ready to register the receiver.
• Hold the button on the receiver pressed (approx. 3 seconds) until the two arrows in
the " " symbol on the temperature controller stop flashing.
• The receiver switches on to indicate the end of the registration process.
Only one receiver can be registered at the temperature controller (a receiv-
er of the RS2W radio switch system, but not a dimmer).
If you start a new registration procedure and register another receiver of
the RS2W radio switch system, the receiver registered previously will be
deleted/overwritten.
d) Deleting a registered receiver
If the receiver is registered at the temperature controller, proceed as follows:
• Start the registration procedure at the temperature controller.
Repeatedly press the "FUNC" button briefly until "CANCEL" appears on the left in
the display.
Hold the "+/ON" button pressed for 2 seconds until the two arrows in the "
symbol flash alternately. Then release the button.
• Hold the "+/ON" button pressed again for 2 seconds and the registered receiver will
be deleted; the right part of the " " symbol and the two arrows disappear.
e) Selecting heating or cooling mode
In heating mode, the receiver is activated when the measured temperature
is below the set target temperature. This operating mode can be used in
conjunction with a heater.
In cooling mode, the receiver is activated when the measured temperature
is above the set target temperature. This operating mode can be used in
conjunction with a cooling unit or fan.
• Repeatedly press the "FUNC" button briefly until "CANCEL" appears in the display.
• Hold the "+/ON" and "-/OFF" buttons pressed at the same time to toggle between
the heating and cooling mode.
Depending on the mode selected, a corresponding symbol appears in the top left of
the display:
" " Heating mode
" " Cooling mode
f) Switching the consumer on/off manually
At the receiver
Follow the operating instructions of the receiver of the RS2W radio switch system.
At the button on the temperature controller
• Repeatedly press the "FUNC" button briefly until "CANCEL" appears in the display.
• The registered receiver can be switched on with the "+/ON" button and switched
off with the "-/OFF" button.
g) Selecting and setting the programme
• Repeatedly press the "FUNC" button briefly until "AUTO" appears in the display.
• Select one of the 8 programmes "PROG1" to "PROG8" with the "+/ON" or "/OFF"
button.
• Hold the "FUNC" button pressed (approx. 3 seconds) until the temperature flashes
at the left in the display.
• Set the temperature with the "+/ON" or "-/OFF" buttons. For quick adjustment, press
and hold down the corresponding button for longer.
• Briefly press the "FUNC" button to confirm and the weekdays will flash.
• Set the weekday or the period using the "+/ON" or "-OFF" buttons.
You can set:
"MO" = Monday
"TU" = Tuesday
"WE" = Wednesday
"
"TH" = Thursday
"FR" = Friday
"SA" = Saturday
"SU" = Sunday
"MO TU WE TH FR" = Monday to Friday
"MO TU WE TH FR SA SU" = Monday to Sunday
• Briefly press the "FUNC" button and the hours of the starting time will flash.
You can now enter a time period during which the set temperature should be main-
tained (e.g. from 8am to 5pm).
Keep in mind that the set time periods must not overlap (e.g. if you would
set programme 1 from 8 am to 5 pm and programme 2 from 9 am to 3 pm).
Otherwise, some switching times or temperatures may not be activated as a
result.
If a temperature is to be maintained for the entire day, set the same time for
starting and ending time.
• Set the hours of the starting time with the "+/ON" or "-/OFF" buttons. For quick
" adjustment, press and hold down the corresponding button for longer.
• Briefly press the "FUNC" button to confirm and the minutes of the starting time will
flash.
• Set the minutes of the starting time with the "+/ON" or "-/OFF" buttons. For quick
adjustment, press and hold down the corresponding button for longer.
• Briefly press the "FUNC" button to confirm and the hours of the ending time will
flash.
• Set the hours of the ending time with the "+/ON" or "-/OFF" buttons. For quick ad-
justment, press and hold down the corresponding button for longer.
• Briefly press the "FUNC" button to confirm and the minutes of the ending time will
flash.
• Set the minutes of the ending time with the "+/ON" or "-/OFF" buttons. For quick
adjustment, press and hold down the corresponding button for longer.
• Briefly press the "FUNC" button to confirm and to exit the setting mode.