Setting Up And Mounting; Maintenance And Cleaning; Operation; Technical Data - VOLTCRAFT SPAS-2400 Bedienungsanleitung

SETTING UP AND MOUNTING

You can place the charger on a heatproof surface or use the adhesive tape on the bottom of the
mounting frame (1) to secure it in place.
• Remove all connected USB devices from the USB charger and unplug the power adapter from the
power adapter socket (2).
• Slide the USB charger from the mounting frame (1).
• To secure the charger to a surface, remove the protective film on the adhesive tape that is attached to
the bottom of the mounting frame.
• Stick the mounting frame to a suitable heat-resistant surface, e.g. a table top.
• Remove the USB charger when it is no longer required. The adhesive tape can be used up to 100 times
to secure the charger to other suitable surfaces. The tape should be cleaned after it has been used
100 times to ensure that it retains its adhesive surface.
• Slide the USB charger back into the mounting frame.
• Connect the USB devices and the power adapter to the USB charger.

OPERATION

Ensure that the connection specifications for your devices comply with the
connection data for the product (see technical data).
Always read the operating instructions for the device that you are going to
charge.
Do not short-circuit the USB ports.
a) Connecting a USB device and turning on the charger
1. Connect the power adapter to the power adapter socket (2) on the charger. For safety reasons, the
output plug cannot be inserted in reverse polarity. The inner contact is positive ("+") and the outer
contact is negative ("–").
2. Insert the power adapter into a normal household mains socket.
3. Turn the charger on or off using the on/off button
is turned off.
4. Once the connected devices have finished charging, turn off the charger using the on/off button
then unplug the power adapter from the mains socket.
b) FUNCTION OF THE USB CHARGING OUTPUTS
• Charging outputs 1, 2, 3 and 4:
Each charging output provides a 5 V/DC output voltage and a maximum output current of 2.0 A.
• Charging outputs 5 and 6:
Each charging output provides a 5 V/DC output voltage and a maximum output current of 2.5 A.
The total maximum output current of all charging outputs is 6.5 A.
c) Connecting and charging USB devices
1. Connect the USB cable on your device to a suitable USB-A port on the charger. Refer to the technical
data of the mobile device that you are going to charge and the output power of the corresponding port.
You can connect up to 6 mobile devices to the charger.
2. Press the on/off button (3) to start the charging process. The USB output ports on the charger start
to deliver a current.
3. Monitor the charging process of your mobile devices. Pause or end the charging process/current flow
by pressing the on/off button .
4. Alternatively, you can also interrupt the charging process by disconnecting the USB cable from the
charger and the mobile device(s).
5. Remove the USB cable from the product and the connected mobile device after charging is complete.
d) LED display - displaying the voltage and charging current
The LED display shows the current voltage and the total current flow during the charging process.
1. Press the switch button for the display (7) to switch between the voltage and current. The LED
display (8) switches between the values for voltage and current at short intervals.
2. Press the switch button twice to only display the voltage.
3. Press the switch button three times to return to the original display and switch between the values for
voltage and current.
The current is only displayed when at least one USB device is connected to a port and the device is
charging or in use. A current must be flowing through the port.
e) Overload protection and automatic switch-off
• If the current exceeds 6.5 A, a countdown begins and "S O S" will appear on the LED display (8).
The device will turn itself off after 30 seconds.
• The LED display switches to sleep mode after 8 minutes. If the total output current of all occupied USB
ports changes, the LED display will turn back on automatically.
(3). The LED display (8) turns off when the charger

MAINTENANCE AND CLEANING

Never use aggressive and abrasive detergents, rubbing alcohol or other chemical
solutions, as these could damage the housing or even impair the functioning of the
product.
• Disconnect the USB cables and connected mobile devices from the product before cleaning.
• Do not immerse the product in water.
• Turn off the product before cleaning and disconnect it from the mains.
• Under no circumstances should you service any of the components in the interior of the product,
therefore never open/dismantle it.
• A dry, soft and clean cloth is sufficient for cleaning. Do not press too hard on the housing as this can lead
to scratch marks.
• Dust can be easily removed using a soft and clean long-haired brush.
DISPOSAL
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.

TECHNICAL DATA

a) USB charger
Input voltage/current ......................................9 - 28 V/DC, max. 3 A
Output voltage/current, ports 1 - 4 .................5 V/DC, max. 2 A
Output voltage/current, ports 5 - 6 .................5 V/DC, max. 2.5 A
Total output current ........................................Max. 6.5 A
Total power consumption ...............................32.5 W
Operating conditions ......................................0 to +70 °C, 10 - 80 % RH
and
Storage conditions .........................................0 to +70 °C, 10 - 80 % RH
Dimensions (W x H x D) ................................88 x 43 x 62 mm
Weight ...........................................................226 g
b) Power adapter
Input voltage/current ......................................100 - 240 V/AC, 50/60 Hz, 1.5 A
Output voltage/current ...................................12 V/DC, 3 A
Legal notice
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing
systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the technical status at the
time of printing.
© Copyright 2016 by Conrad Electronic SE V1_0216_02-DS