Function/Operation; Technical Data - Renkforce 1362940 Bedienungsanleitung

• The twilight switch can be mounted on a vertical wall via two openings (1). To do this,
appropriate screws and, if necessary, plugs must be used.
It is imperative that you pay attention to the correct installation position. On
the rear of the twilight switch you will find an arrow symbol "
head must point vertically upwards, the cable grommets (6) downwards.
The twilight switch may only be mounted to the wall in this position!
Pay attention when drilling and tightening the screws that no cables and pipes are
damaged.
• Pass the connection cables (mains cable and cable for consumer load) through the
rubber seals (6). Cut the rubber seals only as far as necessary so that the connec-
tion cables can be passed through.
• Connect the connection cables (mains cable
and cable for consumer load) with the terminal
clamps (5).
For this purpose, observe the labels on the termi-
nal clamps and the wiring diagram.
The terminal clamp "L1" is the switching output
for the consumer load.
• Once you have carried out the timer and brightness adjustment (see next section),
place the front lid in the correct way.
The small, transparent, round opening of the front lid must located above the
brightness sensor (2).
Furthermore, pay attention that the seal outside in the bottom part is located
correctly in the slot and the plastic cord between the front lid and bottom
part is not pinched.
Afterwards, tighten the 4 casing screws that you removed at the beginning.
Timer and brightness adjustment
• Setting the switch-on time
Using the right control knob (3), you can set the switch-on time for the consumer
load connected.
D-D sunset until sunrise (switched off during the day)
2H Switch-on time 2 hours
4H Switch-on time 4 hours
6H Switch-on time 6 hours
8H Switch-on time 8 hours
• Setting the brightness switching threshold
With the left rotary knob (7), the switching threshold can be set, from which the
ambient brightness at which the twilight switch shall be activated.
Turning the knob to the left in direction of the moon symbol activates the twilight
switch only with great darkness, turning it to the right in direction of the sun symbol
activates the twilight switch in brighter conditions.
• Setting the brightness switching threshold manually
Using the countersunk push-button "M" (4) at the right edge of the twilight switch,
the current brightness can be programmed as switching threshold.
Impress the push button for more than 1 second to save the current brightness.
If you turn the control knob (7), the manual switching threshold will be dele-
ted and the setting of the control dial will be applied.
Function test
If you want to perform a function test after installation, proceed as follows:
• Move the right control knob (3) to the position "D-D" by turning it completely to the
left in counter-clockwise direction.
• The consumer load will not be switched on during daylight hours.
• If you cover the brightness sensor, the connected consumer should be activated after
approximately 10 seconds.
• If you release the brightness sensor again, the consumer load will be switched off
after 10 seconds.

Function/operation

• Setting "D-D":
When the right control knob (3) is in the "D-D" position, the connected consumer
". The arrow
load will be switched on at nightfall (depending on the adjustment of the brightness
switching threshold) and switched off again with sufficient brightness in the mor-
ning.
In order to prevent a continuous switching on/off during short brightness changes,
a time lag of 10 seconds has been provided.
• Setting "2H", "4H", "6H" or "8H":
Upon reaching the adjusted brightness switching threshold, the consumer load will
be switched on for 2h, 4h, 6h or 8h and then switched off automatically.
Should any light fall on the brightness sensor for 10 minutes during this time period,
the consumer load will be switched off (for example, a switched on street light or a
car with lights switched on standing in front of the twilight switch).
Maintenance and care
The twilight switch is maintenance free. For this reason, you should never open it or
take it apart (except for the procedure for installation and connection described in
this manual). Maintenance or repairs may only be performed by qualified personnel.
Clean the transparent lens of the brightness sensor occasionally with a soft clean and
dry cloth. To remove more persistent stains, moisten the cloth with water.
Do not use any aggressive detergent as this might cause discolouration.
Disposal
Dispose of an unserviceable product in accordance with the relevant statu-
tory regulations.
Technical data
Operating voltage............................... 220 - 240 V/AC, 50 Hz
Power input ......................................... <1.8 W
Switching capacity (connector L1) .. 1000 W (resistive load)
...............................................................
Devices with mainly resistive load are, e.g., light bulbs, heaters, etc.
Powered devices with inductive load are, e.g., engines, control gears, con-
ventional transformers, energy-saving bulbs, etc.
Mounting position .............................. Wall mounting (please observe mounting position,
Protection class ................................. IP55
Switching threshold........................... adjustable, 3 - 1000 lux
Switch-on time ................................... 2, 4, 6 or 8h, selectable (or switching on/off auto-
Ambient temperature ........................ -20 °C to +50 °C
Dimensions (H x W x D)..................... 105 x 79 x 36 mm
Weight .................................................. approx. 136 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.
500 W (inductive load)
see section "Installation and connection")
matically, depending on the ambient brightness,
switching delay 10 s)