Renkforce 1243794 Bedienungsanleitung Seite 3

G Operating instructions
RS2W Radio blind switch
Item no. 1243794
Intended use
The product can be used to control a window blind motor wirelessly by radio. Each radio transmit-
ter of the RS2W radio system can be used as a transmitter.
The radio blind switch may only be used on mains voltage (230 V/AC, 50 Hz). A motor with an output
of max. 500 W (~2,2 A) can be connected.
Please read the operating instructions carefully and do not discard them. If you pass the product
on to a third party, please hand over these operating instructions as well.
Any use other than that described above could lead to damage to this product and involves the risk
of short circuits, fire, electric shock, etc. No part of the product may be modified or converted! The
safety instructions must be observed at all times!
This product complies with the applicable national and European requirements. All names of com-
panies and products are the trademarks of the respective owners. All rights reserved.
Package contents
• Radio blind switch
• Operating instructions
Explanation of symbols, inscriptions
The lightning symbol inside a triangle is a warning to inform you of potential risks of
your health and life, such as electrical shock.
This symbol indicates specific risks associated with handling, function and use.
The "arrow" symbol indicates special tips and operating information.
The product is only intended to be installed and used in dry, indoor rooms; it must not
get damp or wet.
Observe the operating instructions!
Safety instructions
R ead the complete operating manual carefully before using the product as it contains
important information about the correct installation and operation.
I f damage is caused by failure to comply with these instructions, it will invalidate the
warranty! We do not assume any liability for any resulting damage!
W e do not assume any liability for material and personal damage caused by improper
use or non-compliance with the safety instructions! In such cases, the warranty will
be null and void!
Warning!
T his product may only be installed by a qualified technician (e.g., an electrician) who
is familiar with the relevant regulations (e.g., VDE)!
I mproper work carried out on the mains voltage endangers not only your own life, but
also the life of others!
I f you do not have the expertise required for the installation, do not install it yourself
but ask a qualified technician.
a) General
• The unauthorised conversion and/or modification of the product is not permitted for
safety and approval reasons (CE). Do not open/disassemble!
• The product is not a toy and does not belong in the hands of children. There is a risk
of a life-threatening electric shock!
• Do not carelessly leave the packaging material lying around since this may become
a dangerous toy for children.
• Handle the product with care; it may be damaged by impacts, blows, or accidental
falls, even from a low height.
b) Operating location
• The product may be used in dry, enclosed indoor areas only; it must not get damp or
wet!
• Only use the product when it is securely installed and steady. Use the product e.g. -
in a suitable flush-mounting or surface mounting or other suitable housing, so that
the required protection against contact is ensured.
• The product must not be exposed to extreme temperatures, strong vibrations or
heavy mechanical stress. Keep the product away from strong magnetic fields, such
as in the vicinity of machinery, electric motors or speakers.
• Do not operate the device in environments where there are high levels of dust, flam-
mable gases, vapours or solvents. There is a danger of fire and explosion!
• Do not use this product in hospitals or medical institutions. Although the transmitter
of the RS2W radio system emits only relatively weak radio signals, these may lead to
malfunction of life-sustaining systems. The same may also apply to other areas.
c) Connection and operation
• This product should never be touched or operated with wet hands. There is a risk of
a life-threatening electric shock!
• The installation may be carried out only if the supply lines to the Radio blind switch
are completely disconnected from the mains voltage. Otherwise, there is a risk of a
life-threatening electric shock!
• An all-pole disconnection from the mains voltage (such as a surge protector) must
be provided as part of the wiring set-up.
• Never connect the product to the power supply immediately after it has been trans-
ferred from a cold room into a warm one (e.g., during transport). The condensation
that forms might destroy the device. Moreover, there is danger of electric shock!
Allow the device to reach room temperature before switching it on. Wait until the
condensation has evaporated. This might take several hours. Only after this should it
be plugged in to the mains supply and put into use.
• Never overload the product. Observe the maximum permissible connection load in
the "Technical data" chapter.
• Do not use the product if it is damaged. There is a risk of a life-threatening electric
shock! In this case, dispose of the product in an environmentally correct manner.
• If it can be assumed that safe operation is no longer possible, the device must be
turned off and precautions must be taken to ensure that it is not used unintentionally.
Do not touch the radio blind switch or any device connected to it.
Disconnect the radio blind switch from the mains voltage by switching off the ap-
propriate circuit breaker or by unscrewing the fuse. Furthermore, turn off the earth
leakage circuit breaker to disconnect all the poles of the mains supply.
• Safe operation can no longer be assumed if:
- the product shows visible signs of damage
- the product does not work at all or works poorly (leaking smoke or a smell of
burning, audible cracking noises, discolouration to the product or the adjacent
surfaces)
- the product was stored under unfavourable conditions
- it was exposed to rough handling during transport
• Use the product only in a temperate climate, never in a tropical climate.
• If you have any questions that are not answered in these operating instructions,
please contact our technical department or another specialist.
Preparations for installation
Please observe the chapter "Safety instructions"!
• Only one motor may be connected to the radio blind switch.
• The radio blind switch cannot detect the end position of the blind. Connect only a motor that can
switch itself off when the end positions at the top and bottom of the blind are reached.
• The radio blind switch to operate must be installed in a proper flush-mounting or surface box or
another suitable housing.
• The installation of the radio blind switch may only be performed when no voltage / current is
applied. Turn off all poles of the electrical power supply by switching off the appropriate circuit
breaker or by unscrewing the fuse and then turn off the associated residual current circuit
breaker (FI circuit breaker).
Secure it against unauthorised reconnection, e.g., with a danger sign. Then check the power
supply for absence of voltage using a suitable measuring instrument.