Renkforce RS2W Bedienungsanleitung Seite 3

G Operating instructions
RS2W Radio-controlled switch E27
Item no. 1243790
Intended use
The radio-controlled switch can be used for remotely switching on and off a screwed-
in E27 light bulb using a suitable radio transmitter of the RS2W system.
The radio-controlled switch may only be used on mains voltage (230 V/AC, 50 Hz). Only
use a light bulb with a maximum output of 100 W (0,43 A).
Please read the operating instructions carefully and do not discard them. If you pass
the product on to a third party, please hand over these operating instructions as well.
Any use other than that described above could lead to damage to this product and
involves the risk of short circuits, fire, electric shock, etc. No part of the product may
be modified or converted! The safety instructions must be observed at all times!
This product complies with the applicable national and European requirements. All
names of companies and products are the trademarks of the respective owners. All
rights reserved.
Package contents
• Radio-controlled switch
• Operating instructions
Explanation of symbols, inscriptions
The lightning symbol inside a triangle is a warning to inform you of potential
risks of your health and life, such as electrical shock.
This symbol indicates specific risks associated with handling, function or
use.
The "arrow" symbol indicates special tips and operating information.
The product is only intended to be installed and used in dry, indoor rooms; it
must not get damp or wet.
Observe the operating instructions!
Safety instructions
R ead the complete operating manual carefully before using the product as
it contains important information about the correct installation and opera-
tion.
D amage due to failure to follow these operating instructions will void the
warranty! We do not assume any liability for any resulting damage!
W e do not assume any liability for material and personal damage caused
by improper use or non-compliance with the safety instructions! In such
cases, the warranty will be null and void!
a) General
• The unauthorised conversion and/or modification of the product is not
permitted for safety and approval reasons (CE). Do not open/disassemble!
• The product is not a toy and does not belong in the hands of children.
There is a risk of a life-threatening electric shock!
• Do not carelessly leave the packaging material lying around since this
may become a dangerous toy for children.
• Handle the product with care; it may be damaged by impacts, blows, or
accidental falls, even from a low height.
b) Operating location
• The product may be used in dry, enclosed indoor areas only; it must not
get damp or wet!
• Only install and use the product tightly screwed into an E27 socket.
• The product must not be exposed to extreme temperatures, strong vibra-
tions or heavy mechanical stress. Keep the product away from strong mag-
netic fields occurring near machines, electric motors or loudspeakers.
• Do not operate the device in environments where there are high levels of
dust, flammable gases, vapours or solvents. There is a danger of fire and
explosion!
• Do not use this product in hospitals or medical institutions. Although
transmitters of the RS2W system only emit relatively weak radio signals,
these may lead to the malfunctioning of life-support systems. The same
may also apply to other zones.
c) Connection, handling and use
• Never touch or operate the product with damp or wet hands. There is a
risk of a life-threatening electric shock!
• An all-pole disconnection from the mains voltage (such as a surge protec-
tor) must be provided as part of the wiring set-up.
• Never connect the product to the power supply immediately after it has
been transferred from a cold room into a warm one (e.g., during transport).
Condensation water that forms might destroy the device. Moreover, there is
danger of electric shock!
Allow the device to reach room temperature before switching it on. Wait
until the condensation has evaporated. This might take several hours.
Only after this should it be plugged in to the mains supply and put into use.
• The radio-controlled switch must never be used without the light bulb in-
serted.
• Never overload the product. Observe the maximally admissible connected
load in the chapter "Technical Data".
• The light bulb will get hot during operation. There is a risk of burning when
touching the light bulb! Allow the light bulb to cool down sufficiently.
• Do not use the product if it is damaged. There is a risk of a life-threatening
electric shock! In this case, dispose of the product in an environmentally
correct manner.
• If it can be assumed that safe operation is no longer possible, the device
must be turned off and precautions must be taken to ensure that it is not
used unintentionally. Do not touch the radio-controlled switch nor an in-
serted light bulb.
Disconnect the radio-controlled switch from the mains by switching off
at the appropriate circuit breaker or by pulling out the fuse. Furthermore,
turn off the earth leakage circuit breaker to disconnect all the poles of the
mains supply.
It can be assumed that safe operation is no longer possible if:
- the product shows visible signs of damage
- the product does not work at all or works poorly (leaking smoke or a
smell of burning, audible cracking noises, discolouration to the product
or the adjacent surfaces)
- the product was stored under unfavourable conditions
- it was exposed to heavy loads during transport
• Use the product only in a temperate and not in a tropical climate.
• If you have any questions that are not answered in these operating in-
structions, please contact our technical department or another specialist.