Changing The Battery; Maintenance And Cleaning; Technical Data - Conrad JG030 Bedienungsanleitung

1 Start mode Time
2 Setting the time
3 Setting the minutes
4 Setting the seconds; by pressing key S2 the display is set to "00"
5 Setting the calendar
6 Setting the month
7 Setting the day
8 Selecting the time format; 12 or 24 hours
c) Stopwatch
• If the stopwatch is not shown, press key S1 until the stopwatch is displayed. Please also refer
to the chapter Functions.
• To start the timer, press key S2.
• To record a split time while the stopwatch is still running press key S3. Then read the split
time. To let the timing proceed, press again key S3.
When the split time is displayed, the stopwatch keeps counting in the background.
• To stop the timer, press key S2.
• To reset the display to zero, press key S3.
d) Countdown timer
• If the timer is not shown, press key S1 until the timer is displayed. Please also refer to the
chapter Functions.
• To set the starting time hold down key S3 until the hour starts flashing.
• Key S2 allows you to change the value of the flashing indicator.
• Key S1 allows you to alternate between hours and minutes.
• Key S3 allows you to exit the set-up at any time. If you do not press a button within 30 sec-
onds, the set-up will exit automatically. The current setting will be saved.
e) Alarm feature
• If the alarm feature is not shown, press key S1 until the alarm is displayed. Please also refer
to the chapter Functions.
• In order to set up the alarm time, hold key S3 down until the hour indicator flashes.
• Key S1 allows you to switch through the different settings.
• Key S2 allows you to change the value of the selected setting.
• Key S3 allows you to exit the set-up at any time. If you do not press a button within 30 sec-
onds, the set-up will exit automatically. The current setting will be saved.
• While the alarm time is shown and no indicator is flashing hold down keyS2 to switch the
alarm on or off. In the display, the alarm icon will either shown or hidden.
• When the alarm timer beeps triggered by the alarm setting, you can stop the alarm using one
of the three buttons.

Changing the battery

• If the display does not show anything, the battery has to be replaced.
• Open the battery compartment cover, on the back of the device. The easiest way to do this,
is to use a small coin that fits into the slot.
To open the cover, move the coin slightly to the left until the cover pops out from the guide.
• Then remove the cover.
• Replace the battery (CR2032). Make sure that the polarity is correct when inserting the new
coin cell. When the display of the stopwatch is facing downwards, the positive pole must point
up.
• Replace the cover and lock it using the coin.
☞
After the battery has been replaced, "00" is flashing on the display. This mode is
used to align the analogue 1/100 display to the correct zero position.
Press key S1 and hold until the analogue pointer is in the zero position (centre up).
To confirm press key S3 briefly until the time is displayed.
• Thereby the battery replacement is completed.

Maintenance and Cleaning

Use a clean, dry and soft cloth for cleaning. If the device is very dirty, use a cloth to slightly
moisten it with lukewarm tap water.
Clean the product very carefully; otherwise you may scratch it.
Do not press too heavily on the glass cover, as this can lead to breakage.
Do not use abrasive cleaning agents, cleaning alcohol or other chemical solutions,
since these could damage the casing or even impair operation.
Disposal
a) Product
Electronic devices are recyclable material and must not be disposed of in the house-
hold waste!
Please dispose of the product, when it is no longer of use, according to the current
statutory requirements.
Remove any inserted battery and dispose of it separately from the product.
b) Batteries and rechargeable batteries
As the end user, you are required by law (Battery Regulation) to return used batteries and
rechargeable batteries. Do not dispose of used batteries in the household waste!
Batteries/rechargeable batteries contain harmful materials and are labelled with
the symbol shown to indicate that disposal in the household waste is forbidden.
The symbols of the critical heavy metals are: Cd=cadmium, Hg=mercury, Pb=lead
(marking can be seen on the battery/rechargeable battery, e.g., underneath the
refuse bin symbol shown on the left).
You can return your flat batteries/rechargeable batteries free of charge at the official collection
points of your community, in our stores, or at places where batteries or rechargeable batteries
are sold!
You thus fulfil your statutory obligations and contribute to the protection of the environment.

Technical data

Operating voltage ................................ 3 V/DC
Power consumption ............................. max. 90 µA
Battery ................................................. 1 Lithium coin cell CR2032, service life approx. 1 year
Weight ................................................. approx. 47 g
Dimensions (W x H x D) ...................... approx. 61 x 81 x 18 mm
Maximum operating temperature ......... 0 °C to +40 °C
Humidity during operation .................... 0% to 90% relative humidity
Maximum storage temperature ............ -10 °C to +50 °C
Humidity during storage ....................... 0% to 100% relative humidity
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau
(www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited. This publication represent the technical status at the time of
printing.
© Copyright 2014 by Conrad Electronic SE.