Characteristics; Unpacking And Assembly; Rescue Deployment; Care And Maintenance - Niviuk CIRES Bedienungsanleitung

1. CHARACTERISTICS

1.1 CERTIFICATION
The CIRES has successfully passed the European EN and LTF certifica-
tion (EN 12491:2001 / LTF 91/09). You can check the certification results
and figures at http://www.para-test.com
1.2 WHO WAS IT DESIGNED FOR? PARACHUTE'S LIMITATIONS
This rescue parachute was designed for the paragliding activity only. It
must not be used nor deployed in velocities reaching over 32 m/s (115
km/h). It is expressly forbidden and can not be used in free-fall.
The maximum load for each side of the parachute is established according
to the certification requirements. The total weight ( payload ) includes:
person, clothing, accessories, glider, harness and parachute.

2. UNPACKING AND ASSEMBLY

2.1 COMPONENTS
The CIRES is delivered with:
• A parachute properly packed in a deployment bag.
• A deployment bag (pod) with central and lateral anchor.
• A 25 cm bridle.
• User's manual.
2.2 PROCEDURE
Check the condition of the parachute and the deployment bag, making
sure there are no abnormalities.
4
2.3 HARNESS ASSEMBLY
We strongly recommend for the process to be supervised by an
authorized dealer or a professional instructor.
The CIRES rescue is compatible with all Niviuk harnesses.
Attaching the rescue parachute's bridle to the harness:
• A suitable screw-gate connector should be used, for example; 7mm,
square, Stainless Steel maillon (Maillon Rapide type).
• Connect the reserve parachute handle to the pod which will vary
depending on the harness model and reserve parachute pocket
location (center or side).
• Place the properly packed CIRES inside the inside the reserve para-
chute container.
• Fasten the deployment handle in its place.
• Close the reserve parachute container flaps, insert the safety pin and
check its operation.
• Harness models without an integrated reserve parachute pocket will
need to be outfitted with a corresponding outer container (front mount
or otherwise).
• Repeat the same steps to install an outer reserve parachute container.
CAUTION!
After installing the reserve parachute in its container, it is mandatory to
conduct a hang-test. Be certain for the handle to open all the container
flaps prior the parachute extraction while evaluating the force amount
exerted during the pull to jettison the rescue system.
After a conclusive outcome, reinstall the reserve parachute by following
the same procedure as before.
2.4 PRE-FLIGHT CHECK
Before each flight, check that:
• There is no visible damage that could affect its airworthiness.
• The rescue parachute container is correctly closed with the safety
pin(s) in place.
• The deployment handle is correctly and securely fastened and all
parts are in good condition.
Any part of the harness/reserve/handle using Velcro must regularly
have it separated and re-attached to prevent 'bedding in' over time
which could impede a successful reserve parachute deployment
sequence.

3. RESCUE DEPLOYMENT

It is vital to periodically guide your hand toward the rescue handle and
feel its location in flight. Memorizing the gesture to the point of becoming
second nature will become an asset in case of an emergency.
In the event of an emergency, the pilot must quickly evaluate the AGL
(Altitude Above Ground Level) and decide whether or not to deploy
the emergency parachute. Deploying the rescue when the glider is
recoverable may increase the risk of injury. If there is sufficient eleva-
tion (AGL), you have sufficient height and the glider is in a flat spin, it
is preferable to first try to stop the spin (e.g. full stall), due to the risk
of entanglement. On the other hand, a second hesitation in deploying
the reserve could prove costly if there is insufficient height.
3.1 DEPLOYMENT PROCEDURE
If the rescue must be deployed, the procedure should be as follows:
• Look for the rescue handle and grasp it firmly with one hand.
• Pull firmly upwards/sideward on the handle to unfastens its Velcro
and releases the safety pins keeping the reserve parachute container
closed. The pod extraction from the container will then take place.
• Look for a clear area, then throw and let go the reserve parachute
handle with the pod attached to it away from harness and paragli-
der. Throwing the reserve parachute in the downwind direction will
speed-up its opening sequence. Throwing it opposite to the spinning
direction will also help prevent tangling with the glider.
• After deployment, avoid entanglement, pendulum motions and pos-
sible downplaning, by pulling the glider in as symmetrically as possible
with the B, C, D or brake lines.
• On landing, do a PLF (Parachute Landing Fall) to minimize the risk of
injury if the terrain surface permits it.
• Once on the ground, deflate the canopy by pulling one of the reserve
parachute lines to avoid the possibility of being dragged.

4. CARE AND MAINTENANCE

4.1 MAINTENANCE
The CIRES rescue parachute will be repacked at 180 day intervals
to insure airworthiness. When necessitated by climate, storage, or
condition the equipment maintenance specialist may require additional
maintenance.
We always recommend for this rescue parachute to be inspected
and repacked by a trained and certified professionals. Additional
inspections should be performed if there is any suspicion of damage
or excessive wear.
After a deployment, the reserve parachute should be checked by the
distributor or manufacturer. Always seek professional advice whenever
in doubt.
The materials used in the CIRES rescue have been carefully selected
for maximum durability. Nevertheless, maintaining your rescue
following the guidelines below will extend its lifetime.
ENG ES
5