Renkforce RCW-5002E-03 Bedienungsanleitung Seite 4

If the ST/STP button (4) is pressed longer in the settings, adjustments take place quicker.
Setting the time of the second time zone (DT)
• Hold down the RESET (3) key, until the seconds starts flashing.
• Press the ST/STP button (4) to reset the second display to "00".
• Press the RESET button (3) to proceed to the next setting (hours).
• Use the ST/STP button (4) to set the hour.
• Press the RESET button (3) to select the next setting and adjust in the following sequence the
minutes, year, month and date, as described above. With the RESET button (3) the value to be set
will be selected and with the ST/STP button (4) the value to be set can be adjusted.
• Press the MODE button (2) to save the settings and to complete the process.
Timer function (CD)
Setting the time target:
• Hold down the RESET (3) key, until the seconds start flashing.
• Adjust seconds, hours and minutes as described for "Setting the time for the second time zone".
The maximum time setting is 99:59:59 h.
• With the RESET button (3) the value to be set will be selected and with the ST/STP button (4) the
value to be set can be adjusted.
• Press the MODE button (2) to save the settings and to complete the process.
How to use the timer:
• Press the ST/STP (4) button to start the timer. The time counts down to "00:00:00".
• While the timer is counting down, you can stop the process or restart the timer by using the
button ST/STP (4).
• After the lapse of the set time you can hear an alerting beep for about 20 seconds, which can be
deactivated by pressing the buttons MODE (2), RESET (3) or ST/STP (4).
Stopwatch function (ST)
• Press the ST/STP button (4) to start the stopwatch.
• Press the button ST/STP (4) again to stop the stopwatch function.
• By pressing the button RESET (3) you can reset the stopwatch to "00:00:00", after it was halted.
• If you press on RESET (3) while the stopwatch is still running, the meantime will be displayed,
while the stopwatch continues counting down in the background.
• Press the RESET button (3) again to return back to the current time display. This process can be
repeated several times.
Alarm function (AL)
Setting the alarm time:
• Hold down the RESET (3) button, until the hour starts flashing.
• Adjust seconds, hours and minutes as described for "Setting the time for the second time zone".
• With the RESET button (3) the value to be set will be selected and with the ST/STP button (4) the
value to be set can be adjusted.
• Press the MODE button (2) to save the settings and to complete the process.
After setting the alarm time, the alarm function is activated automatically.
Activating/deactivating the alarm function and the night light function:
• When the alarm function is displayed, briefly press the ST/STP (4) button several times to switch
the alarm function and the hour signal on or off.
• When the respective function is enabled, the corresponding symbol (7 and/or 9) is displayed.
Alarm procedure:
• The alarm will turn on for approx. 30 seconds at the set time.
• Press the button MODE (2), RESET (3) or ST/STP (4) to activate the snooze function. In that case
the alarm will resound after approx. 5 minutes. The alarm symbol (7) is flashing during this time.
• Proceed as described under "Activating/deactivating the alarm function and hour signal" to
turn the alarm function off.
Setting of time for automatic DCF synchronisation (RF)
Here you can set the timing at which the clock will automatically search for the DCF signal for the
daily synchronization.
• Hold down the RESET (3) button, until the hour start flashing.
• Adjust seconds, hours and minutes as described for "Setting the time for the second time zone".
• With the RESET button (3) the value to be set will be selected and with the ST/STP button (4) the
value to be set can be adjusted.
• Press the RESET button (2) to save the settings and to complete the process.
Manual time setting (TM/ seconds are flashing)
If a time signal reception is not possible, you can set the watch manually.
• The seconds are already flashing when this operating mode is selected.
• Press the ST/STP button (4) to reset the second display to "00".
• Press the RESET button (3) to proceed to the next setting (hours).
• Use the ST/STP button (4) to set the hour.
• Press the RESET button (3) to select the next setting and adjust in the following sequence the
minutes, year, month and date, as described above. With the RESET button (3) the value to be set
will be selected and with the ST/STP button (4) the value to be set can be adjusted.
• Press the MODE button (2) to save the settings and to complete the process.
Display Light
• Press the LIGHT button (1) to turn on the back light function for a few seconds.
Changing the battery
• If the display contrast fades or the device no longer works, the battery has to be replaced.
• Replacing the battery should be done by a specialist, using special clockmaker tools and profes-
sional knowledge.
• To replace the battery, the back of the casing is removed.
• The battery can then be removed from its holder and be replaced.
Maintenance and cleaning
Apart from replacing the batteries, the product does not require any maintenance and should
never be disassembled.
Please use a soft, dry, clean cloth for cleaning.
Do not use aggressive detergents as these can cause discolouration of the case.
Water and shock resistance
The wristwatch is protected against impacts that can occur with normal everyday use. Neverthe-
less, do not expose it to extreme shocks such as might occur if it falls onto a hard surface. This
could damage the clock mechanism.
The indication 5 ATM means that the watch is suitably protected when washing hands, washing
the car, etc., and can be worn during a bath or when taking a shower.
However, this is not a diver's watch.
Disposal
a) Product
Electronic devices are recyclable material and must not be disposed of in the house-
hold waste!
Please dispose of the product, when it is no longer of use, according to the current
statutory requirements.
Remove the battery if there is one inserted and dispose of it separately from the product.
b) Batteries and rechargeable batteries
As the end user, you are required by law (Battery Regulation) to return used batteries. Do not
dispose of used batteries in the household waste!
Batteries/rechargeable batteries contain harmful materials and are labelled with the
symbol shown to indicate that disposal in the household waste is forbidden. The sym-
bols of the critical heavy metals are: Cd=cadmium, Hg=mercury, Pb=lead (marking can
be seen on the battery/rechargeable battery, e.g., underneath the refuse bin symbol
shown on the left).
You can return used (rechargeable) batteries free of charge at the official collection
points in your municipality, our stores, or where ever (rechargeable) batteries are sold!
You thereby fulfil your statutory obligations and contribute to the protection of the environment.
Technical data
Operating voltage.........................................3 V/DC
Battery ...........................................................1 x 3 V-lithium coin cell CR2025
Battery life .....................................................approx. 2 years
Time protocol ................................................DCF77
Countdown timer ..........................................max. 99:59:59 h
Snooze function............................................approx. 5 min
Water resistance .........................................5 ATM
Weight ............................................................42 g
Declaration of conformity (DOC)
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, 92240 Hirschau, hereby declare that this
product adheres to the fundamental requirements and the other relevant regulations of Directive
1999/5/EC.
You can find the conformity declaration for this product at www.conrad.com
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.