Herunterladen Diese Seite drucken

Mains Connection; Generating Compressed Air; Care And Maintenance; Periodic Maintenance - Metabo Basic 260 Betriebsanleitung

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 3
4.2

Mains connection

B
Danger! High voltage
Operate machine in dry envi-
ronment only.
Operate machine only on a power
source complying with the following
requirements:
− outlets properly installed, earthed
and tested;
− fuse protection in accordance
with the Technical Specifications.
Position power cable so it does not
interfere with the work and is not
damaged.
Always check to see that the machine
is switched OFF before plugging in.
Protect
power
cable
aggressive liquids and sharp edges.
Use only extension cables with suffi-
cient lead cross section (see "Techni-
cal Specifications").
Do not stop the compressor by
unplugging, but switch OFF using the
switch.
Unplug after use.
4.3
Generating compressed
air
1.
Start compressor (14) and wait until
the max. tank pressure is reached
(compressor shuts off).
The tank pressure is indicated by
the tank pressure gauge (15).
15
17
2.
Set pressure regulator (16) to
required working pressure. The cur-
rent working pressure is indicated
by the regulated pressure gauge
(17).
A
Caution!
The regulated pressure may
not be set higher than the max. wor-
king pressure of the connected air
tools!
3.
Connect air hose to compressed air
outlet (18).
4.
Connect air tool.
You are now ready to work with the
air tool.
5.
Switch the compressor OFF, if you
do not continue working immediately
afterwards. Unplug after switching
OFF.

5. Care and Maintenance

A
Danger!
Prior to all servicing:
− Switch Off.
− Unplug.
− Wait until the compressor has
come to a complete stop.
− Ensure the compressor and all air
tools and accessories connected
to it are relieved from pressure.
After all servicing:
from
heat,
− Check to see that all safety
devices are operational.
− Make sure that no tools or other
parts
machine.
Repair and maintenance work other
than described in this section must
only be carried out by qualified spe-
cialists.
5.1

Periodic maintenance

Prior to each use
Check
replace if necessary.
check all screwed connections for
tightness, tighten if necessary.
14
Check power supply cable for dam-
age, if necessary have replaced by
16
a qualified electrician.
Every 50 operating hours
Check air intake filter (19), clean if
necessary.
18
Drain condensate (20).
remain
on
or
in
the
air
hoses
for
damage,
19
20
ENGLISH
Every 250 operating hours
Replace air filter element.
5.2

Machine storage

1.
Switch unit OFF and unplug.
2.
Release pressure from tank and all
connected air tools.
3.
Store machine in such way that it
cannot be started by unauthorized
persons.
A
Caution!
Do not store machine unpro-
tected outdoors or in damp environ-
ment.

6. Trouble Shooting

A
Danger!
Prior to all servicing:
− Switch Off.
− Unplug.
− Wait until the compressor has
come to a complete stop.
− Ensure the compressor and all air
tools and accessories connected
to it are relieved from pressure.
After all servicing:
− Check to see that all safety
devices are operational.
− Make sure that no tools or other
parts
remain
on
machine.
Compressor does not run:
No mains voltage.
− Check cables, plug, outlet and
mains fuse.
Mains voltage too low.
− Use only extension cables with
sufficient lead cross section (see
"Technical Specifications"). Avoid
using extension cable with cold
machine.
Compressor
was
unplugging.
− Switch compressor OFF at the
On/Off switch, then ON again.
Motor has overheated, caused by
insufficient cooling (cooling fins cov-
ered).
− Remove cause for overheating
and allow to cool down for
approx. 10 minutes, then start
again.
Compressor runs but does not build
up sufficient pressure.
Check valve leaky.
− Have check valve serviced by
qualified service centre.
or
in
the
stopped
by
9

Quicklinks ausblenden:

Werbung

loading