Werbung
Verfügbare Sprachen
Verfügbare Sprachen
13.3 cm (5.25") Panel Mount Multi-card
Reader USB 3.0
Item no. 41 75 77
1. Intended use
The product is intended for installation in a 13.3 cm (5.25") slot of a computer housing. On the front, there are
various connection sockets, a fan control and a card reader for reading out / recording cards of different types.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be
avoided under all circumstances.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
2. Delivery content
• Panel mount multi-card reader
• USB 2.0 cable
• Power cable (4-pin)
• SATA cable
• USB 3.0 cable
• Audio cable
3. Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
Persons / Product
• Pay attention to electrostatic charge when dealing with electronic components. Before touching electronic
components, first touch a metal surface so as to discharge any static charges that have accumulated.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become dangerous playing material
for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture,
flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any
accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
• Also observe the safety and operating instructions of any other devices which are connected to the product.
Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our technical
support service or other technical personnel.
4. Operating elements
1 2
3 4 5
6
7
14
13
Ill. 1
1
Power indicator (shines during operation)
2
Card reader indicator (shines while reading and
recording)
3
SM/XD slot
4
CF/MD slot
5
microSD slot
6
MMC/SD slot
7
MS slot
417577_v1_1112_02_m_cs6.indd 2
Version 11/12
• 2 x fan cable
• 4 x screw
• Operating instructions
8
9
12
11
10
8
Fan speed controller (1)
9
Fan speed controller (2)
10 Earphone input
11 Microphone input
12 eSATA connector
13 USB 3.0 port
14 USB 2.0 port
5. Installation
When in doubt about how to install the device correctly, please contact an EXPERT or a
specialist workshop and let them carry out the installation.
In case of improper installation, the product as well as your computer and all connected
devices will be damaged.
Lethal Danger!
Switch off the computer in which the product is to be installed and all connected devices
and separate all devices from the mains voltage. Unplug the mains plug! To switch the
device off via the ON/OFF switch is not enough!
A
B
C
H
G
F
E
Ill. 2
1. Open the housing of your computer and carefully take off the lid of the housing.
2. Look for a free 13.3 cm (5.25") installation slot and remove the front cover. There may be a metal shield
behind it which needs to be removed. For some housings it can be screwed off, for some it has to be
carefully broken out. Depending on the housing the complete front cover of the housing has to be removed
beforehand.
3. Attach the connection cables included to the corresponding connections on the multi-card reader (see Ill. 2).
4. Power is supplied via a special Y cable. Attach the small two-pole plug to the connection (A) and the large
two-pole plug to the connection (E).
5. Connect the USB 2.0 cable to the connections (D) and (C) and connect the SATA cable to the
connection (G) on the multi-card reader. Connect the audio cable to the connection (H).
6. Connect one fan cable each to the connections (B).
7. Push the cables and the multi-panel into the 13.3 cm (5.25") bay of your computer housing; then bolt down
the multi-card reader with the enclosed screws.
8. Now connect the cables of the multi-card reader to the corresponding connections of your mainboard. Note
the information in the instructions provided by the mainboard manufacturer.
9. Connect the USB 3.0 cable to the USB 3.0 connection on the mainboard.
10. Connect the two fan cables with the corresponding fans in the computer.
11. Connect the 13.3 cm (5.25") power cable to a corresponding electrical connection on your computer
power supply unit.
12. Lay the cables in a way so that they cannot get into a fan of the PC. Use cable binders for fastening.
13. Check all connections once more and then close the housing of your computer.
14. Connect your computer and monitor with the mains voltage und switch on all devices.
15. If your computer does not start correctly, switch it off immediately and check all settings and cable
connections.
6. Operation
1. Connect the external devices and memory cards to the correspondingly designated connections on the
multi-card reader.
2. The two rotary knobs on the front of the multi-card reader are for setting the speed of two fans. A turn of the
knob anti-clockwise reduces the fan speed; turning it clockwise increases the speed.
The following card types can be read simultaneously: XD, CF, MS, SD.
Card types that CANNOT be read simultaneously include SD and microSD.
7. Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
8. Technical data
Supported card formats:
SD, SDHC, SDXC, microSD, microSDHC, microSDXC, miniSD, CF, MD,
xD, MMC, RS-MMC, MMCmicro, MMC 4.0, MS, MS Duo, MS PRO, M2,
MS PRO-HG, MS PRO-HG Duo
Front connections:
4 x USB 2.0, 2 x USB 3.0, eSata, Audio (In/Out)
USB standard:
USB 3.0 / USB 2.0 / USB 1.1
Operating systems:
Microsoft® Windows 98SE (drivers required*), ME (drivers required*),
2000, XP (Home, Pro, with SP1, SP2, SP3) only 32-bit,
Vista™ (32/64-bit), 7 (32/64-bit), 8, 8 Pro, Enterprise, RT,
Mac OS (9.0 or higher), Linux (2.4.18 or higher)
Weight:
203 g (multi-card reader)
*You can find the required software drivers for downloading at www.conrad.de on the associated product page under
the "Dokumente & Downloads" tab ("Documents & downloads").
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
All rights including translation reserved. Reproduction by any method, e.g.
photocopy, microfilming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
© 2012 by Conrad Electronic SE.
A
12 V/DC connection
B
Fan connection
C Card reader connection
D USB 2.0 connection
E
5 V/DC connection
F
USB 3.0 connection
G SATA connection
H Audio connection
D
V1_1112_02-JH
11/22/2012 11:38:40 AM
Werbung
