Conrad Design Bedienungsanleitung Seite 3

O P E R A T I N G I N S T R U C T I O N S
SATA hard disk enclosure "Design"
Item no. 41 60 90
Intended use
An 8.89 cm/3.5" SATA hard disk can be installed in the enclosure. The connection to a com-
puter is made via a USB port. The wall plug transformer enclosed is used to supply the power.
Always observe the safety instructions and all other information included in these
operating instructions.
This product complies with the applicable National and European requirements. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
Package Contents
• Enclosure with an installed interface converter (without hard disk)
• Wall plug transformer
• USB cable
• Accessory kit (aluminium stand, 2 plastic feet with 2 matching rubber feet, set of screws)
• Operating Instructions
Features
• An 8.89 cm/3.5" SATA hard disk (not enclosed) can be installed
• USB 2.0 port (USB 1.1 compatible)
• Using the stand provided, the installation is possible with the minimum requirements for
space.
• On/off button with integrated LED on the front (lights up when the power supply is active or
fl ashes during read/write access)
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequen-
tial damage!
Nor do we assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions! In such cases,
the warranty will be null and void.
• The unauthorised conversion and/or modifi cation of the product is not permitted for
safety and approval reasons (CE).
• The product is not a toy. Keep devices that operate on the mains voltage out of the
reach of children. Therefore, be especially careful when children are around.
Use the product where it is out of the reach of children.
• The product is only intended for use in dry, indoor locations. No part of the product
should be allowed to become damp or wet; never take hold of it if your hands are
wet!
Use of the wall plug transformer involves the risk of a potentially fatal electric
shock!
• The design of the wall plug transformer complies with protection class II. Only use
a standard mains socket as the power source for the wall plug transformer.
• Only use the wall plug transformer provided to power the hard disk enclosure.
• Do not pull the wall plug transformer from the mains socket by pulling on the cable.
Take hold of it on the sides of the housing and pull it out of the mains socket.
• If the wall plug transformer is damaged, do not touch it; there is danger to life from
electric shock!
First, switch off the mains voltage to the socket to which the wall plug transformer
is connected (switch off at the corresponding circuit breaker, remove the safety
fuse or switch off at the corresponding RCD protective switch, so that the socket
is fully disconnected).
You can then unplug the wall plug transformer from the mains socket. Dispose of
the faulty wall plug transformer in an environment-friendly way, do not use it any
more. Replace it by a wall plug transformer of the same design.
• Do not leave packing materials unattended. They may become dangerous play-
things for children.
• Handle the product with care, it can be damaged by impacts, blows, or accidental
drops, even from a low height.
Installation of a hard disk
www.conrad.com
• Remove the two screws on the enclosure's rear and remove the plastic cover.
• Pull out the drawer from the aluminium frame, and bear in mind the correct alignment!
Version 10/11
• Position a SATA hard disk correctly on the terminal strip of the board and
then screw it fi rmly into the drawer with four suitable screws.
• Push the drawer back into the aluminium frame (pay attention to the drawer's correct orienta-
tion!).
• Position the back enclosure cover correctly and screw it fi rmly in place; this also secures the
drawer in the aluminium frame.
• If you wish to place the hard disk enclosure in the vertical position, you may use either the
aluminium stand enclosed or fi rmly screw the two plastic feet to the bottom of the hard disk
enclosure .
If you are using the plastic feet, also affi x the two large rubber feet enclosed.
Driver installation
The driver for the hard disk enclosure is included in your operating system (minimum require-
ment Windows XP or higher).
For this reason, there is no enclosed driver data carrier.
Connection
• Switch on your computer, if you have not done so yet, and wait until the operating system has
fi nished loading.
• Connect the round low-voltage plug from the enclosed wall plug transformer to the corre-
sponding socket on the back of the hard disk enclosure.
• Connect the wall plug transformer to the mains voltage, plug it into a mains socket.
• Connect the USB connector, on the rear of the hard disk enclosure, to a free USB 2.0 port on
your computer using the USB cable supplied.
• Switch on the hard disk enclosure by briefl y pressing the button on the front. The LED in the
button lights up.
• When starting up for the fi rst time, Windows recognises the hard disk enclosure automatically
and completes the driver installation (the drivers are included in Windows (e.g. Windows XP,
Windows Vista, Windows 7).
A new hard disk has to be partitioned and formatted fi rst, before the drive is displayed in
Explorer and can be used, see next section.
Partitioning / formatting the hard drive
• In Windows XP/Vista or Windows 7, the partitioning and formatting is very easy to perform
from the Control Panel. For example, in Windows XP select the function "Administrative tools"
in the control panel and then the functions "Computer management", "Storage" and fi nally
"Disk Management"..
This is where you select the correct new hard disk and create a new partition.
• After partitioning, the newly created partition has to be formatted (fast formatting is suffi cient;
"normal" formatting may take a long time to complete, depending on the size of the hard disk).