Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
O P E R A T I N G I N S T R U C T I O N S
SATA Hard Disk Drive Enclosure
„DataTale „TDM11H"
Item-No. 41 28 15
Intended Use
A 8.9cm/3.5" SATA hard disk drive can be installed in the enclosure. The connection to a
computer is made via a USB2.0 port or eSATA interface.
This product complies with the applicable National and European requirements. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
Package Contents
• Casing with integrated interface converter
• USB cable
• eSATA cable
• Set of screws
• Power adaptor
• Adhesive pad
• Operating Instructions
Safety Instructions
The warranty will be void in the event of damage caused by failure to
observe these safety instructions!
We do not assume any liability for any consequential damage!
We do not assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions. The
warranty will be void in such cases.
• The unauthorised conversion and/or modification of the product is inadmissible
because of safety and approval reasons (CE). Never dismantle the product!
• The design of the AC adaptor complies with safety class II. Only supply the pow-
er adaptor with a voltage from a standard mains socket connected to the public
supply grid.
• This product is not a toy, and should be kept out of the reach of children.
Children cannot assess the dangers arising from incorrect use of electrical
devices. Be especially careful if children are around.
• Only use in dry indoor locations. The product must be protected from damp and
wet, as there is a risk of a fatal electric shock! Never touch the product with wet
hands.
• Do not expose the product to extreme temperatures (< 0°C or > +40°C), direct
strong sunlight, strong vibrations, high humidity or strong mechanical stress.
• Do not leave packaging material lying around carelessly. It may become a
dangerous plaything for children.
• Never use the product immediately after it has been brought from a cold room
into a warm one. Condensation that forms might destroy the device.
Furthermore, there is a danger of an electric shock.
Wait until the product reaches room temperature and the condensation has
evaporated. This may take several hours.
Then connect the AC adaptor to the power supply and start to use the product.
• Handle the product with care, it can be damaged by impacts, blows, or accidental
drops, even from a low height.
Controls
www.conrad.com
Version 01/10
°
1 On/Off button with integrated power/access LED
2 Low voltage socket for connecting the external power adaptor
3 eSATA connector
4 USB port Type B
5 Attachment option for anti-theft protection (available at specialist dealers)
6 Locking lever
7 Hard disk (not included in the delivery)
8 Adhesive pad (to be attached to the front of the hard disk; protection against contact with the
hot hard disk)
9 Bracket to pull out the hard disk
Installation of a SATA Hard Disk
• Carefully pull out the aluminium bracket from the front of the enclosure.
• Attach the aluminium bracket to your 8.9cm-/3.5"-SATA
hard disk using the four screws enclosed.
To do this, place the hard drive with the circuit board on a flat,
clean surface (1).
Place the bracket on the side of the hard drive that is on the
opposite side to the ports (2).
Fix the bracket to the hard disk using the four special screws
(3) enclosed.
Check whether the bracket can be easily moved after
tightening (4).
Then, stick the adhesive pad on to the hard disk, i.e. on the
side of the hard disk that is between the bracket and the hard
disk (see illustration in section „Controls").
The adhesive pad is used to prevent contact with the hot hard
disk, thus preventing skin burns.
• Unlock the two locking levers, by positioning them vertically
(A).
• Carefully insert the hard disk into the enclosure and pay atten-
tion to the correct orientation.
The special screws allow the hard drive to be easily inserted
into the enclosure.
• Lock the hard disk in the enclosure, by turning the locking
lever as shown in figure B.
In addition to 8.9cm-/3.5" hard disks, with of conventional
installation height, flat 8.9cm-/3.5" hard disks can also be
used.
Changing the Hard Disk
If you use several hard drives, each of the drives can be provided with a separate bracket (addi-
tional brackets and special screws are available as optional accessories; they are not included
in the delivery).
Thus, several hard drives can be changed quickly and safely.
Caution!
Unlock the locking lever, see figure „A" above (set the lever upright) and pull out the hard disk
from the enclosure using the bracket.
Insert another hard disk and secure it with the locking levers (turn the levers as shown in figure B).
1
5
2
3
4
Before changing a hard disk, switch off the enclosure!
Then wait at least 20-30 seconds, until the motor or the magnet disk(s) for the hard
disk have come to a halt.
Only then may the hard disk be removed from the enclosure.
Otherwise there is the danger of loss of data, and moreover the read/write heads
could touch the magnet disk and damage the hard disk!
Transport and store the hard disks with utmost care.
6
6
7
8
9
A
B
Werbung
Inhaltsverzeichnis
