Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Lighting console
Item no. 59 14 58 (3-Channel)
Item no. 59 14 60 (4-Channel)
Item no. 59 12 79 (6-Channel)
1.
Intended use
This product is used to generate lighting effects on dance floors, in party rooms etc. With a tongue and groove
joint, the individual elements can be arranged in a variety of shapes. It is approved only for connection to a
standard wall socket. Do not use other power supplies. It must only be used in enclosed spaces and therefore
not outside. Contact with moisture must be avoided at all times.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
2.
Delivery content
•
Lighting console
•
Operating instructions
3.
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
Persons / Product
•
The illuminant and housing of the device will get very hot during operation. Do not touch elements including
an illuminant during or shortly after operation.
•
Ensure proper ventilation of the product. Do not cover it during operation. There is a danger of fire.
•
Before replacing an illuminant or rearranging elements of the lighting console, turn the device off and let it
cool off for half an hour. Disconnect the mains plug from the wall socket.
•
When rearranging the elements handle them only by touching the housing. Do not apply pressure on the
illuminants.
•
After replacement, wipe the new illuminant clean using a clean, dry cloth.
•
Position the product in such a manner that it cannot fall down.
•
Always arrange the elements of the product in such a way that they form a robust structure.
•
Objects that are illuminated must be at least 0.5 m from the light source of the device. Easily flammable
materials such as decorative fabrics must have at least a distance of 0.5 m from the device. Otherwise
there may be a fire hazard!
•
Always lay the cables so that nobody can trip over or become entangled in them. This poses a risk of
injury.
•
Never look directly or with optical instruments into the light beam.
•
Point the light beam in such a way that it is directed below eye level.
•
The device is not a toy. Keep it out of the reach of children and pets.
•
Do not leave packaging material lying around carelessly. These may become dangerous playing material
for children.
•
Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture,
flammable gases, vapours and solvents.
•
Do not place the product under any mechanical stress.
•
If it is no longer possible to operate the product safely, take it out of operation and protect it from any
accidental use. Safe operation can no longer be guaranteed if the product:
-
is visibly damaged,
-
is no longer working properly,
-
has been stored for extended periods in poor ambient conditions or
-
has been subjected to any serious transport-related stresses.
•
Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the
product.
•
Also observe the safety and operating instructions of any other devices which are connected to the
product.
Miscellaneous
•
Consult an expert when in doubt about operation, safety or connection of the device.
•
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified
shop.
•
If you have questions which remain unanswered by these operating instructions, contact our technical
support service or other technical personnel.
4.
Setup
•
Arrange the effect beamer by sliding the elements carefully onto each other. Make sure that the tongue and
groove fit properly into each other.
•
Also ensure that the effect beamer is always assembled as a robust and steady structure.
•
Place the effect beamer onto an even, clean surface.
5.
Operation
1.
To use the effect beamer, connect the mains plug to a standard wall socket.
2.
Turn the "Music" control dial and the "Speed" control dial counterclockwise as far as they will go.
3.
Turn the effect beamer on using the on / off switch.
4.
To use the effect beamer as a chaser light, turn the "Speed" control dial clockwise until the required speed
is set.
5.
To use the effect beamer for music synchronisation, additionally turn the "Music" control dial clockwise and
set the required microphone sensitivity.
6.
After use, turn the effect beamer off using the on / off switch.
7.
If you will not use the product for a longer period of time, unplug the mains plug from the wall socket.
6.
Replacing illuminant
1.
Before replacing the illuminant, let the effect beamer cool down and unplug the mains plug from the wall
socket.
Version 11/11
2.
Carefully turn the illuminant in a counterclockwise direction to unscrew it from the lamp socket. Never touch
it with bare hands. Use a clean, dry cloth to hold the illuminant.
3.
Screw a new illuminant into the lamp socket by turning it in a clockwise direction.
7.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
8.
Technical data
Item no.
Illuminant colours:
Type of illuminant:
Illuminant output:
Operating voltage:
Operating temperature:
Dimensions (W x H x D):
Weight:
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
All rights including translation reserved. Reproduction by any method, e.g.
photocopy, microfilming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
© 2011 by Conrad Electronic SE.
59 14 58
59 14 60
blue, red, yellow
blue, red, yellow, green
E27
E27
3 x 40 W
4 x 40 W
220 – 240 V/AC, 50Hz
220 – 240 V/AC, 50Hz
-10 to +45 °C
-10 to +45 °C
140 x 488 x 139 mm
350 x 243 x 135 mm
1.14 kg
1.26 kg
59 12 79
blue, red, yellow, green,
purple, orange
E27
6 x 40 W
220 – 240 V/AC, 50Hz
-10 to +45 °C
365 x 348 x 135 mm
1.78 kg
V1_1111_02-JU
Werbung
