Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operation
a) Setting the time automatically
• Once the battery is installed properly, all the hands of the clock will set itself to
the 12 o'clock position. The clock will then receive radio signals (may take 3 - 10
minutes) and synchronize the clock time with a local radio transmitter.
• The clock automatically receives radio signals 4 times a day (2:00, 3:00, 4:00, 5:00) to
ensure accurate clock time.
• In order to initiate the automatic search for a radio signal at any given time, press
and hold the REC button for 3 seconds during normal operation. All the hands will set
itself to the 12 o'clock position. The clock will then set the time again automatically
by synchronizing with a local radio transmitter. If the clock time cannot be set within
10 minutes, the device will apply the clock time displayed last.
b) Setting the time manually
• Press and hold the M.SET button for 5 seconds.
• Continue to press and hold the M.SET button to advance the minute hand. Release
the button to stop the advance.
• Press the M.SET button once to advance the minute hand by 1 minute.
• Release the M.SET button when done, the clock will resume movement after a few
seconds.
c) Cancelling the clock time setup
Press the RESET button to cancel the current time setting. All the hands will set itself
to the 12 o'clock position. The clock will then set the time again automatically by
synchronizing with a local radio transmitter.
d) Checking temperature
The indoor temperature is shown on the display located at the 6 o'clock position.
Maintenance and cleaning
• The product is maintenance-free except for potential battery replacement and
occasional cleaning.
• Do not use any abrasive or chemical cleaners.
• Never submerge the product in water to clean it.
• To prevent scratch marks, do not apply too much force on the surface during
cleaning.
• Use a dry, clean, soft and lint-free cloth to clean the housing. To remove tougher
stains, slightly dampen the cloth with lukewarm water. You may use a little soap or
a mild cleaning agent.
Declaration of Conformity (DOC)
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare
that this product conforms to the fundamental requirements and the other relevant
regulations of the directive 1999/5/EC.
The Declaration of Conformity for this product can be found at
www.conrad.com.
Disposal
a) Product
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the
relevant statutory regulations.
Remove any inserted (rechargeable) batteries and dispose of them
separately from the product.
b) (Rechargeable) batteries
You as the end user are required by law (Battery Ordinance) to return all used batteries/
rechargeable batteries. Disposing of them in the household waste is prohibited.
Contaminated (rechargeable) batteries are labelled with this symbol to
indicate that disposal in the domestic waste is forbidden. The designations
for the heavy metals involved are: Cd = Cadmium, Hg = Mercury, Pb = Lead
(name on (rechargeable) batteries, e.g. below the trash icon on the left).
Used (rechargeable) batteries can be returned to collection points in your
municipality, our stores or wherever (rechargeable) batteries are sold.
You thus fulfil your statutory obligations and contribute to the protection of the
environment.
Technical data
Power supply .......................................1 x 1.5 V/DC battery, AA type (not included)
Thermometer range ............................0 ˚C to +50 ˚C
Operating conditions ..........................0 ˚C to +50 ˚C, 20 – 90 % RH
Storage conditions..............................0 ˚C to +50 ˚C, 20 – 90 % RH
Dimensions (Ø x D)..............................172 x 58 mm
Weight ...................................................355 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the
technical status at the time of printing.
© Copyright 2016 by Conrad Electronic SE.
V3_0216_02-ETS-Mkd
Werbung
Inhaltsverzeichnis
