Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
6. Terminal assignments of plugs
ATX connector (20+4)
GND (black)
+3.3 V/ DC (orange)
+5 V/ DC (red)
+12 V1/ DC (yellow)
+5 V/ DC (red)
+12 V1/ DC (yellow)
+5 V/ DC (red)
+5 V/ DC Standby (mauve)
(not assigned)
Power OK (grey)
GND (black)
GND (black)
+5 V/ DC (red)
GND (black)
GND (black)
GND (black)
PS ON (green)
+5 V/ DC (red)
GND (black)
GND (black)
+3.3 V/ DC (orange)
-12 V/ DC (blue)
+3.3 V/ DC (orange)
+3.3 V/ DC (orange)
7. Tips & Notes
• The power unit is in "standby" mode after it had been switched off with the power button on the ATX housing
(similar to a television).
• The ATX power unit has a certain power input in "standby" mode. This is why you should also switch off
the ATX power supply unit via the mains switch in order to save energy, if you don't need your computer.
• If your motherboard has the 4-pin ATX2.0 connection for the +12-V voltage, connect it to the corresponding
connection of the ATX power unit.
• The port is usually used to provide a better supply to the switch-mode controls on the motherboard (which
generate the current/voltage for the CPU) and to reduce the load of the +12V cable of the ATX current
connector. If the plug is not connected the motherboard may not start.
• If the computer does not start when you press the button on the front of the computer housing, check
whether the mains switch of the ATX power unit is switched on (position "I").
• If you have just assembled the computer, check whether all cables are connected correctly. Are the boards
plugged in correctly, is the CPU fan connected? If the graphics card has a separate bus bar, it has to be
connected with the appropriate connector of a power unit!
8. Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
9. Technical data
Output power:
max. 300 W
Operating voltage:
230 V/ AC
Standby power consumption:
< 1 W
Plugs:
2 x SATA, 3 x Molex (4-pin), 1 x Floppy Drive (4-pin),
1 x ATX2.0 +12 V (4-pin), 1 x ATX (20+4-pin)
MTBF:
min. 80,000 h (at 25 ºC)
Fan Ø:
120 mm
Operating temperature:
0 to +40 ºC
Dimensions (W x H x D):
140 x 86 x 151 mm
Weight:
approx. 1.07 kg
Output voltage:
+3.3 V
+5 V
Output current max.:
19 A
15 A
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
All rights including translation reserved. Reproduction by any method, e.g.
photocopy, microfilming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
© 2012 by Conrad Electronic SE.
Floppy Drive
Molex connector (4)
plug (4)
+5 V/ DC (red)
GND (black)
GND (black)
+12 V1/ DC (yellow)
SATA connector
ATX2.0 connector (4)
GND (black)
+12 V2/ DC (yellow)
+12 V2/ DC (yellow)
GND (black)
+12 V1
+12 V2
-12 V
9 A
9 A
0.3 A
+12 V1/ DC (yellow)
GND (black)
GND (black)
+5 V/ DC (red)
+12 V1/ DC (yellow)
GND (black)
+5 V/ DC (red)
GND (black)
+3.3 V/ DC (orange)
+5 V (Standby)
2.5 A
V2_0912_02-KV
Werbung
Inhaltsverzeichnis
