Technical Data; Maintenance And Cleaning - Eurochron EDT 4002 Bedienungsanleitung

count-down mode (timer mode)
- Press the button T1 (1) or T2 (2) to select the desired timer.
- Set the desired count-down time with the buttons HR (4), MIN (5) and SEC (6):
Press HR to set the hours
Press MIN to set the minutes
Press SEC to set the seconds
- Press the button S/S (7) to start the count-up timer.
- While the timer runs down, the button of the activated timer T1 or T2 flashes
green.
- Press the button S/S (7) again to stop the count-down timer or to restart it.
- When the time running down has reached 0:00:00, an alarm signal sounds, the
time display runs forward again and the corresponding timer button T1 or T2
flashes red.
- Press the button S/S (7) to stop the alarm signal.

If the alarm is not stopped, it switches off automatically after one minute.
- The previously set count-down time appears again in the display.

As soon as a count-down time has been set, the count-down symbol (down
arrow) appears in the display next to the corresponding timer.
The timer can then be used only as a count-down timer.
In order for the timer to be used again as a count-up timer, the programmed
count-down time must be deleted again by pressing the RESET button com-
bination (8).
Programming a count-down time recorder
With this function, you have the option to save a fixed time setting for the count-
down timer so that you do not always have to enter the count-down time again.
This is especially an advantage if you want to use a frequently recurring time set-
ting.
- Press the button T1 (1) or T2 (2) to select the timer for which a time default
should be programmed.

A different time default can be programmed for each of the two timers.
- Press and hold the M button (3) for about 2 seconds, until the display indicator
blinks.
- Set the desired count-down time with the buttons HR (4), MIN (5) and SEC (6):
Press HR to set the hours
Press MIN to set the minutes
Press SEC to set the seconds
- Press the M button (3) again or wait 30 seconds to store the set count-down
time.
- Thereafter, the programmed count-down time can be recalled repeatedly by
pressing the button M (3).

To store a new time default, simply repeat the procedure described above
and thereby overwrite the old programming.
- The use of a count-down timer with the time preset is the same as the use of a
normal count-down timer (see further above).
setting of the alarm signal
The alarm volume is set with the switch mute/lo/hi (9):
- mute: Alarm is muted
- lo: quiet alarm volume
- hi: loud alarm volume

maintenance and cleaning

The product does not require any maintenance and should never be disassembled
for any reason.
Please use a soft, dry, clean cloth for cleaning.
Do not use any chemical cleaning agents, as they can discolour the plastic housing.
disPosal
a) Product
Electronic devices are recyclable waste materials and must not be dis-
posed of in the household waste!
Please dispose of the product, when it is no longer of use, according to
the current statutory requirements.
Remove any inserted battery and dispose of it separately from the prod-
uct.
b) batteries and rechargeable batteries
The end user is legally obliged (Battery Regulation) to return used batteries and
rechargeable batteries. Do not dispose of used batteries in the household waste!
Contaminated batteries/rechargeable batteries are labelled with these
symbols to indicate that disposal in the domestic waste is forbidden. The
symbols for the relevant heavy metals are: Cd=cadmium, Hg=mercury,
Pb=lead (marking can be seen on the battery/rechargeable battery, e.g.,
underneath the refuse bin symbol shown on the left).
You can dispose of your used batteries/rechargeable batteries free of charge at your
community's collection point or any place where batteries/rechargeable batteries
are sold!
You thereby fulfil your statutory obligations and contribute to the protection of the
environment.

technical data

Operating voltage: ...........................................3 V/DC (2 batteries of type AAA/Micro)
Current consumption: .....................................max. 26 mA
Battery life: .......................................................approx. 2.5 years
Timer: .................................................................2
Time preset storage: .......................................2
Max. time display: ............................................99 h 59 min 59 s
Dimensions: ......................................................90.5 x 76.5 x 21.5 mm
Weight: ...............................................................86 g
Operating temperature: .................................0 to +45°C
Storage temperature: .....................................-15 to +55°C
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com). All rights including translation reserved. Reproduction by
any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is prohibited. These ope-
rating instructions represent the technical status at the time of printing. Changes in technology
and equipment reserved.
© copyright 2014 by conrad electronic se.