Sygonix Slave Bedienungsanleitung Seite 3

Operating instructions
GB
Ceiling-Mounted Motion Detector
("Slave")
Intended use
The product is exclusively intended for the expansion of the related ceiling-mounted
motion detector with the Sygonix order number (33988W).
The motion detector is intended for installation in a room ceiling.
The motion detector's integrated PIR sensor responds to temperature changes within
the detection range, e.g. when a person enters the detection range.
It then activates the output of the controller, whereby e.g. a light or other load is
switched on for an adjustable amount of time.
A total of 6 motion detectors can be connected to the controller of the "master" mo-
tion detector (the "master" motion detector and up to 5 further "slave" motion detec-
tors).
On the "slave" motion detector, only sensitivity setting is possible; the time and bright-
ness settings are made solely using the "master" motion detector.
Any other use than that described above may damage the product. Moreover, this
may give rise to hazards such as short-circuiting, fi re, electric shock, etc. No part of the
product may be modifi ed or converted!
Always observe the safety instructions and all other information included in these op-
erating instructions! Read the operating instructions carefully and keep them safe for
later reference.
This product complies with the applicable national and European requirements. All
names of companies and products are the trademarks of the respective owner. All
rights reserved.
Package Contents
• Motion detector ("Slave")
• Connection cable (approx. 5 m) with double connector
• Plastic cover for limiting the PIR sensor opening angle
• Operating Instructions
Explanation of the Symbols
The lightning symbol indicates a health hazard, e.g. electric shock.
This symbol indicates specifi c risks associated with handling, function and
use.
The "arrow" symbol indicates special tips and operating information.
Safety Instructions
Read the complete operating manual carefully before using the product,
as it contains important information about the correct installation and
operation.
The warranty will be void in the event of damage caused by failure to ob-
serve these safety instructions! We do not assume any liability for any
consequential damage!
We do not assume any liability for material and personal damage caused
by improper use or non-compliance with the safety instructions! The
warranty will be void in such cases!
Caution!
This device should be installed only by people with relevant electrotech-
nical knowledge and experience!
With an improper installation, you risk:
- Your own life;
- The life of the user of the electrical system.
With an improper installation, you risk severe material damage, e.g. through
fi re. You face the risk of personal liability for damage to people and material.
Contact an electrician!
The home technology brand for the entire house. More information at www.sygonix.com
• The unauthorised conversion and/or modifi cation of the product is not al-
lowed for safety and approval reasons (CE).
• The product is not a toy and must be kept out of the reach of children! There
is a risk of a lethal electric shock!
• This product is only to be installed and used in dry conditions indoors. The
product must not get damp or wet as this may damage it; danger of a fatal
electric shock!
• Do not use this product in rooms or under adverse ambient conditions
where combustible gases, vapours or dust are or may be present! There is a
risk of explosion!
• The product must not be exposed to extreme temperatures, strong vibra-
tions or heavy mechanical stress.
• If you have reason to assume that safe operation is no longer possible,
disconnect the product immediately and secure it against accidental opera-
tion. After this, let an expert check the product.
It can be assumed that safe operation is no longer possible if:
- The product shows visible signs of damage,
- The product does not work at all or works poorly (fl ickering light, leaking
smoke or a smell of burning, the light fl ickers, audible cracking noises, dis-
colouration to the product or the adjacent surfaces.)
- The product was stored under unfavourable conditions
- It was exposed to heavy loads during transport
• Do not leave packaging material carelessly lying around since it could be-
come a dangerous plaything for children.
• In commercial institutions, the accident prevention regulations of the Em-
ployer's Liability Insurance Association for Electrical Systems and Operating
Facilities are to be observed!
• If you have any questions that are not answered in this manual, please con-
tact our technical service or another specialist.
Function of the motion detector
The PIR sensor integrated in the motion detector responds to temperature changes
within the detection range, e.g. if a person whose temperature is different from the
background enters the detection range.
The detection range of the PIR sensor can be limited with the provided plastic cap,
which is easily placed on the motion detector (if necessary, individual segments of the
plastic cap can also be removed).
The range for detecting motion is determined by several factors:
• The motion detector's mounting height
• Temperature difference between the moving object and the background (ambient)
• The size of the object
• The distance of the object from the motion detector
• Direction and speed of the movement
• Ambient temperature
After switching on the mains voltage for the controller, it takes about 30 seconds until
the PIR sensor in the motion detector has adjusted to the background temperature
and is able to recognise changes in temperature within the detection range, and a
switching procedure is triggered.