Technical Data; Maintenance And Cleaning - Conrad 55 54 23 Bedienungsanleitung

Inserting/removing the MicroSD memory card
The camera can be operated only with the MicroSD card inserted.
The blue LED lights up for approx. 2 seconds if no memory card is inserted or if the memory
card is full. Then the camera switches off automatically.
Always switch the camera off before inserting or removing a memory card. Doing
so while the camera is switched on could otherwise lead to loss of data or to the
memory card being destroyed.
a) Inserting the memory card
• First, remove the dust protection cap from the camera by turning the cap in the anti-clockwise
direction.
• Insert the MicroSD memory card with the contact surface facing the USB port.
Ensure that the memory card latches into the MicroSD slot "6" of the camera with an audible
click.
• Seal the camera again carefully with the dust-protection cap "4".
b) Removing the memory card
Press the memory card in briefl y and then remove it from the camera.
Setting the Time and Date
During recording, the date and time of clicking is displayed at the bottom right of the camera.
Proceed as follows to adjust the date and time:
1. Create a new text fi le on the storage medium
2. Name the fi le "TIME"
3. Open the fi le and enter the date and time in the following format:
- 2013 06 08 06 09 01 (Year Month Day Hours Minutes Seconds) (there should be a blank
space between the numbers)
Start recording
Press the ON/OFF button "2" briefl y once. The green and blue LED fl ashes.
The camera starts recording as soon as the blue LED starts fl ashing.
To stop, press the ON/OFF button "2" for at least 2 seconds. The camera saves the recording
on the inserted MicroSD memory card and then switches off automatically.
Reading the fi les
• Switch off the camera.
• Remove the dust protection cap "4" from the camera by turning the cap in the anti-clockwise
direction.
• Connect the USB cable to the camera and your computer.
• Your computer recognises the camera with the inserted MicroSD memory card as removable
media.
• The data could also be read with the help of a standard card reader. To do this, please follow
the steps given in the Chapter "Inserting/removing the micro-SD memory card".

Maintenance and Cleaning

The product is maintenance-free. Never dismantle the product. There are no serviceable parts
inside. The rechargeable battery is permanently installed and cannot be replaced.
The entire product can be cleaned easily with a moist cloth. For this, use a soft cloth.
Never use caustic cleaning agents or chemical solutions, as they could damage the surface of
the casing. Do not press too strongly to prevent damage to the product.
Disposal
Dispose of the unserviceable product in accordance with the relevant statutory
regulations.

Technical Data

Power supply......................................Lithium-polymer rechargeable battery, 550 mAh
(permanently integrated, cannot be replaced)
Rechargeable battery duration ........ 1.5 – 2 hours
Temperature range .......................... -5°C to +40 °C
USB Standard .................................. 2.0
Video format .................................... H.264
Resolution: ....................................... 1280 x 720 pixel
Sensor type ..................................... 3 Megapixel
Viewing angle of lens ....................... 135°
Frame rate ....................................... 30 frames/sec
Storage medium .............................. MicroSD memory card up to 32 GB
Protection class ............................... IP68
Dimensions ...................................... 24 x 84 mm (Ø x L)
Weight ............................................. 32.5 g
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2013 by Conrad Electronic SE.