System Requirements - VOLTCRAFT DSO-1052 USB Kurzanleitung

3. CONTENTS
DSO
Measurement program on Mini-CD, (with detailed instructions from the "Help" option in the
menu)
USB Y connecting cable
Quick guide
4. DESCRIPTION OF THE PARTS DSO
1 Earth connection, reference potential
2 Calibration output 1kHz/2 Vp-p square wave signal
3 BNC trigger input external
4 BNC measurement input channel 2
5 BNC measurement input channel 1
6 Opening for ventilation
7 USB XI connection for multi-instrument operation - not available -
8 USB Type B connection
5. INSTALLING THE MEASUREMENT PROGRAM
Before you connect the DSO to a computer, install the measurement program.
Switch on the computer and start the operating system.
Insert the enclosed software CD into the CD drive and close it. The automatic start mode will
automatically start the installation of the measurement program.
If this does not happen automatically, start the program "setup.exe" by double-clicking in
Explorer, of your operating system, on the drive holding the CD-ROM. The software installa-
tion will start.
Please follow the on-screen instructions.
In the start menu's program manager, a new folder called "DSO-XXXX" is created.
Leave the CD in the drive, for device installation.
6. CONNECTION AND INSTALLATION OF THE DSO
Connect the enclosed USB-Y connecting cable to two free USB ports on your computer and
then with the USB connection (8) on the DSO.
The operating system recognises the new hardware and starts the "Hardware Wizard".
Follow the on the screen instructions.
Choose the installation option "Install software automatically (recommended)" and press
"Continue".
The system searches for the compatible driver. Follow the instructions on screen until, you
are asked to restart the operating system. Restart the computer, to update the new installa-
tion.
7. STARTING THE MEASUREMENT PROGRAM
Start the computer and connect the USB connector from the computer to the DSO, before
starting the program. Open the start menu, or the "DSO-XXXX" program on the desktop
screen, by double-clicking on the icon.
The measurement program's start screen appears and initialises the DSO. Select your model,
if necessary. The DSO is ready for use.
Using the program key "AUTO" (Autoset) all parameters for the DSO are set auto-
matically, so the optimum signal display appears on screen.
8. CLEANING
Always observe the following safety instructions before cleaning the device:
Live components may be exposed, if the covers are opened or parts removed
(unless this can be done without tools).
Prior to cleaning or repairing of the device, all cables have to be detached and
the device has to be turned off.
Do not use any cleaning agents containing carbon, petrol, alcohol or the like to clean the
product. The surface of the device could be corroded. Furthermore, the fumes are hazardous
to your health and are explosive. Moreover, you should not use sharp-edged tools, screw-
drivers or metal brushes or suchlike for cleaning.
For cleaning the device or the display and the measuring cables, use a clean, slightly damp,
fuzz-free, antistatic cloth.
Should questions arise concerning the use of the device, feel free to contact
our technical support at the following phone number:
Voltcraft®, 92242 Hirschau, Lindenweg 15, Tel. No. 0180 / 586 582 7.
9. DISPOSAL
Electronic products are raw material and do not belong in the household waste.
When the device has reached the end of its service life, please dispose of it,
according to the current statutory requirements, at your local collecting site.
Disposing of fl at batteries in the household waste is prohibited.
10. TECHNICAL DATA / SPECIFICATIONS
The detailed data can be found in the help fi le (Help) in the measurement program.
General DSO-1052
Measurement inputs
Feed impedance
Max. input voltage
Input connection
Test probe ratio
Defi nition
Bandwidth (-3 dB)
Ramp-up time
Sampling rate
Storage capacity max.
Nauwkeurigheid
Trigger mode
Display mode
Software
Power supply
Working temperature
Mass
Dimensions (LxWxH)

SYSTEM REQUIREMENTS

Windows® computer as a minimum, 1 GHz Pentium® or compatible with at least 128 MB
RAM, graphics resolution 800 x 600, CD-ROM, 2x USB 2.0, 500 MB free hard disk memory,
Windows® XP/VISTA or higher.
Legal notice
These operating instructions are a publication by Voltcraft , Lindenweg 15, D-92242 Hirschau/Germany, Phone +49 180/586 582 7
®
(www.voltcraft.de).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming, or the capture in electronic data processing
systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2012 by Voltcraft
®
DSO-1082 DSO-1102
USB USB USB
Two separate channels CH 1 and CH 2
1 MOhm // 25 pF
35 V/DC or 35 Vp/AC
DC-AC-GND
1:1, 10:1, 100:1, 1000:1
8 bit
50 MHz 80 MHz 100 MHz
≤ 7 ns ≤ 4.3 ns ≤ 3.5 ns
150 MS/s 250 MS/s
64 kpts
± 3%
Auto, norm, single
Y-t, X-Y
Windows® XP/VISTA or higher
USB-bus powered, 2x USB
0°C to +40°C,
rel. humidity < 80%, non-condensing
ca. 430 g (without accessories)
approx. 205 x 38 x 125 mm
DSO-2202
USB
9 bit
200 MHz
≤ 1.7 ns
1 Mpts