Maintenance And Cleaning; Technical Information - Renkforce RS2W Bedienungsanleitung

Switch on/off or dim the luminaire via the control key
Briefly press the control key at the front of the wireless socket to activate the last used
brightness level or to switch the light off.
Pressing the key longer will reduce or increase the brightness.
That is:
After each dimming procedure, when the control key is released, the dim-
ming direction (increasing/decrease) reverses. You can easily adjust the
desired brightness yourself.
Holding down the control key will have no effect, if the connected luminaire
is turned off - first, activate the dimmer and the connected luminaire by pressing the
control key briefly.
The LED on the control key shows the actual status:
• LED is on: wireless socket/luminaire are on
• LED is off: wireless socket/luminaire are off
Programming the the wireless socket to a radio transmitter
The wireless socket can be taught-in to any radio transmitter of the RS2W
radio system.
Follow the operating instructions of the radio transmitter that you are going
to use prior to the teaching procedure.
During teach-in, maintain a 20 - 30 cm minimum distance between the wire-
less socket and the radio transmitter. Failing to do this may result in a regis-
tration failure.
• If the wireless socket and the luminaire are turned on (LED on the control key is on),
switch off the wireless socket first.
The wireless socket must be switched off (LED on the control key is off), or
else the teach-in process cannot be performed.
• Start with the registration process on the radio transmitter.
Example: On a 12-channel hand-held radio transmitter of the RS2W radio system
press the keys "ON" and "OFF" of the desired switch channel, such as Channel 1,
simultaneously until the red LED of the hand-held radio transmitter starts flashing.
Release both keys, the red LED keeps flashing and the registration mode is enabled.
• Hold the control key on the wireless socket down as long as the registration process
is complete.
Example: On a 12-channel hand-held radio transmitter of the RS2W radio system the
LED lights up blue and then goes dark. Now release the control key of the wireless
socket.
• The wireless socket switches on (last available brightness level), and indicates that
the registration process is complete. The red LED on the control key is on.
Up to 5 receivers can be taught-in to a switch channel of a radio transmitter
of the RS2W radio system.
It is also possible to register the wireless socket on several radio transmit-
ters.
However, do not register the wireless socket and a radio switch together on
a single channel of a radio transmitter!
Always register the wireless socket on a separate channel of the radio
transmitter.
Deleting a taught-in wireless socket from a radio transmitter
The procedure corresponds exactly to the teach-in procedure of the the wireless
socket on the radio transmitter. For more information, see the operating instructions
for the radio transmitter of the RS2W radio system to be used.
Switching on/off by radio transmission
The wireless socket can be turned off wirelessly only when it has been registered on
a radio transmitter of RS2W radio system.
Refer to the above description and the operating instructions for the radio transmitter
to be used.
Example for a 12-channel hand-held radio transmitter of the RS2W radio sys-
tem: The brightness of the luminaire connected to the wireless socket can
be set to several levels (0% -> 25% -> 50% -> 75% -> 100%) by pressing the
corresponding "ON" key of the programmed channel briefly. Pause briefly
between each keystroke until the blue feedback LED on the hand-held radio
transmitter goes dark!
Dimming down (100% -> 75% -> 50% -> 25% -> 0%) works in the same way
by using the "OFF" key on the programmed channel.
Pressing the "ON" key twice in rapid succession activates the luminaire at
100% brightness. Pressing the "OFF" key twice in rapid succession turns the
luminaire off.
Maintenance and cleaning
The product does not require any maintenance and should never be opened or dis-
sembled for any reason. Repair or maintenance work must be carried out by a spe-
cialist.
Disconnect the wireless socket from the mains every time before cleaning by un-
plugging it from the electrical outlet. Disconnect a connected load from the wireless
socket.
You can use a clean, dry, soft cloth for cleaning. Dust can be very easily removed with
a soft, clean brush and a vacuum cleaner.
Do not use aggressive, chemical or scouring cleaning agents, as this may lead to dis-
colouration or changes in the material on the surface.
Range
The transmission range of the radio signals between the radio transmitter of the RS2W
radio system and the wireless socket is up to 150 m under optimum conditions.
This value, however, is the so-called "open space range" (the range when
transmitter and receiver are visible to each other, without interfering influ-
ences).
In practice, however, there may be walls, room ceilings, etc. between the transmitter
and the receiver which will reduce the range accordingly.
Due to the different influences on the radio transmission, no specific range can be
guaranteed. However, trouble-free operation is usually possible in a single family
house.
Sometimes the range can be considerably reduced due to:
• Walls, reinforced concrete ceilings, light-weight walls with metal post and beam
construction
• Coated/metallised insulated glass
• Proximity to metallic & conductive objects (e.g., heating elements)
• Proximity to human bodies
• Other devices using the same frequency (e.g. headphones or loudspeakers)
• Proximity to electric motors/appliances, transformers, power-supply units, computers
Declaration of conformity (DOC)
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, herewith de-
clare that this product conforms to the fundamental requirements and the other rel-
evant regulations of the directive 1999/5/EC.
The declaration of conformity for this product is available at:
www.conrad.com
Disposal
The product must not be disposed of in the household waste.
Dispose of the product at the end of its serviceable life in accordance with
the current statutory requirements; e.g., return it to any suitable collection
point.
Technical information
Operating voltage....................................... 230 V/AC, 50 Hz
Power consumption................................... approx. 0.2 W
Connection power...................................... 25 - 300 W (0,1 - 1,3 A)
Suitable load ............................................... 230 V light bulbs, high-voltage halogen lamps,
Dimmer type ................................................ phase cut
Transmission/reception frequency ......... 868.3 MHz
Range ........................................................... up to 150 m (see chapter "Range")
Protection class ......................................... I
Child safety lock ......................................... yes
Ambient conditions .................................... Temperature 0 °C to +45 °C, air humidity 0% to
Dimensions (H x W x D)............................. 106.5 x 55 x 36 mm (without plug)
Weight .......................................................... approx. 120 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.
conventional halogen transformers, dimm-
able high-voltage LED lamps
90% relative, not condensing