Dust/Chip Extraction; Starting Operation - Bosch GOP 12V-28 Professional Originalbetriebsanleitung

20 | English
Sanding sheet Material
– Paint
– Varnish
– Filler
– Bodyfiller
Attaching/changing the sanding sheet on the sanding
plate
The sanding plate (15) is fitted with a hook-and-loop fasten-
ing, allowing sanding sheets with a hook-and-loop backing to
be secured quickly and easily.
Tap the hook-and-loop fastening of the sanding plate (15)
before fitting the sanding sheet (16) to facilitate maximum
adhesion.
Position the sanding sheet (16) so that it is flush with one
side of the sanding plate (15), then place the sanding sheet
on the sanding plate and press it on firmly.
To ensure optimum dust extraction, make sure that the
punched holes in the sanding sheet are aligned with the
drilled holes in the sanding plate.
To remove the sanding sheet (16), take hold of it by a corner
and pull it away from the sanding plate (15).
You can use all sanding sheets, polishing and cleaning
fleeces from the Delta 93 mm series in Bosch's range of ac-
cessories.
Sanding accessories such as fleece/polishing felt are at-
tached to the sanding plate in the same way.

Dust/chip extraction

The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Connecting the dust extraction system (see figure A)
The dust extraction system (14) is only designed for use
with the sanding plate (15); it serves no purpose when used
together with other application tools.
1 609 92A 4A6 | (11.06.2018)
Application
For sanding down paint
For sanding undercoats (e.g. removing brushstrokes,
paint drips and paint runs)
For final sanding of primers prior to painting
Always connect a dust extraction system for sanding.
Remove the application tool for fitting the dust extraction
system (14) (accessory).
Slide the dust extraction system (14) as far as it will go over
the tool holder (7) onto the collar of the power tool. Turn the
dust extraction system to the required position (not directly
under the power tool). Push the clamping lever (17) shut to
fix the dust extraction system in position.
Attach the dust extraction adapter (19) of the dust extrac-
tion hose (20) to the dust extraction outlet (18). Connect
the dust extraction hose (20) to a dust extractor (access-
ory).
You will find an overview of connecting to various dust ex-
tractors on the graphics pages.
The dust extractor must be suitable for the material being
worked.
When extracting dry dust that is especially detrimental to
health or carcinogenic, use a special dust extractor.
Operation

Starting Operation

Inserting the battery
Use only original Bosch lithium-ion batteries with the
u
voltage stated on the type plate of your power tool.
Using other batteries can lead to injuries and pose a fire
hazard.
Note: The use of batteries unsuitable for your power tool can
lead to malfunctions or damage to the power tool.
Insert the charged battery (3) into the handle until you feel it
engage and it is flush with the handle.
Switching on/off
Make sure that you are able to press the On/Off switch
u
without releasing the handle.
To switch on the power tool, slide the on/off switch (1) for-
ward so that "I" appears on the switch.
To switch off the power tool, slide the on/off switch (1)
backward so that "0" appears on the switch.
Note: If the power tool shuts down automatically because
the battery is flat or overheated, switch the power tool off
using the on/off switch (1).
Charge the battery or let it cool down before switching the
Grit
Coarse 40
60
Medium 80
100
120
Fine 180
240
320
400
Bosch Power Tools