Renkforce RF-GT-X1 Bedienungsanleitung Seite 4

• Select the key to be redefined by pressing on the physical keyboard. The new definition for the key
appears in the input line.
• Confirm your selection with "OK" and click on the "Apply" software key. The key on the virtual keyboard
model is now defined with the key pressed on the physical keyboard.
b) Key setting (macro setting)
• Select a profile M1, M2 or M3 by clicking with the cursor.
• Select a key on the virtual keyboard model on the right-hand side of the software window. An input line
opens in the window. Select the "Macro setting" setting.
• Determine a macro with the "+" key and tap a name, if necessary. Delete a macro with the waste bin key.
• Select a macro from the drop-down menu and start recording with the "Record" key. Pressing this key
again ends recording and saves the macro.
• Delete steps within the macros with "Delete" or "Clear" and navigate with "Top", "Up", "Down" and "Bottom".
In addition, you can also set a delay "Record delay" and cycles "Cycles".
c) Key setting (multimedia)
• Select a profile M1, M2 or M3 by clicking on the respective tabs with the cursor.
Key setting (function key)
You can use the key assignments for each of the three assignment profiles (M1, M2 and M3)
according to your wishes. Repeat these settings for the other profiles.
d) Setting the light-change effect program
• Insert a checkmark next to "Light" to be able to set the light effect programs via the software menu.
These light effect programs are switched with the key combinations outlined in "Operation b) Setting the
keyboard".
• In the drop-down menu to the right, you can select from six different named light-change effects.
Depending on the selected light-change effect program, certain variables can be software set for the
different light effects.
- Set the brightness with the slider under "Bright".
- Set the speed of the colour change with the slider under "Speed".
- Using the direction arrows, set the direction of the colour change, if the light effect program permits it.
- Select a colour in the "Single" drop-down menu.
- The "RGB" box switches the additive RGB colour mode on or off.
The various setting options are not available for all light-change effect programs in the same
manner.
The following settings can be implemented for the user-defined "Define" program:
• Select a profile M1, M2 or M3 by clicking on the
respective tabs with the cursor.
• Select a different key (or key to be assigned)
on the virtual keyboard model on the right-
hand side of the software window. An input line
opens in the window. The "Single key" setting
is pre-selected if no user-defined settings are
available.
• Select the name of a macro for the key to be
assigned. If no macros are available, you can
create one yourself.
• Assign a name and use the software keys
to record the macros. You can also start the
macro editor directly from the "Macro editor"
tab.
• Confirm the selected macro with "OK" and
press the "Apply" software key. The key is now
defined with a macro.
• Select a key on the virtual keyboard model on
the right-hand side of the software window.
An input line opens in the window. Select the
"Multimedia" setting.
• In the drop-down menu, select a multimedia
function for the key.
• Confirm the selected macro with "OK" and
press the "Apply" software key. The key is now
defined with a multimedia function.
• Select a profile M1, M2 or M3 by clicking on the
respective tabs with the cursor.
• Select a key on the virtual keyboard model on
the right-hand side of the software window.
• An input line opens in the window. Select the
"Function key" setting.
• Select a function for the key from the "Function
key setting" drop-down menu.
• Confirm the function with "OK" and press the
"Apply" software key. The button is now defined
with the selected function.
• In the "Single" drop-down menu, you can select a colour or freely
define a colour.
• In the "Background" drop-down menu, you can select a
background colour or freely define a background colour.
• In the "Tool" menu, you can select the keys individually or delete
your selection.
e) Resetting
• Restore your settings for a profile to the factory settings with "Reset to default".
• Confirm the reset.
Care and cleaning
• Always disconnect the product from the power supply before cleaning it.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these could damage the
housing or stop the product from functioning properly.
• Use a dry, lint-free cloth to clean the product.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to protection of the environment.
Technical data
Power supply ........................................ via USB, 5 V/DC, 300 mA
Cable length ......................................... 160 cm
Supported operating systems ............... Windows
Vista™ (32 Bit), 7 (32/64 Bit), 8.0 (32/64 Bit), 8.1 (32/64 Bit),
10.0 (32/64 Bit), 10S, RT
Operating conditions ............................. +45 ºC, 60 - 80 % relative humidity (non-condensing)
Storage conditions ................................ +65 ºC, 60 - 90 % relative humidity (non-condensing)
Dimensions (W x H x D) ....................... 237 x 154 x 40 mm
Weight .................................................. 515 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE.
2000, XP (Home, Pro, with SP1, SP2, SP3) (32 Bit),
®
*1620193_v1_0618_02_DS_m_2L_(1)