Grundig RR 720 CD Serviceanleitung Seite 5

Operating Hints
This chapter contains excerpts from the operating instructions. For further particulars please refer to the appropriate user instructions the part number of which is indicated in the
relevant spare parts list.
CONTROLS
Top and front panel the picture shows: RR 760 CD
p
– connection for headphones
FUNCTION
VOLUME – to adjust the volume.
SURROUND SOUND
SURROUND – to switch the surround sound VOLUME
effect
SOUND – on and off
FUNCTION
– CD: to switch to CD mode
– TAPE: to switch to TAPE mode
– RADIO: to switch to RADIO mode
ANTENNA – telescopic aerial for FM
reception
DIGITAL SOUND CONTROL DSC – to select the
desired sound effect: CLASSIC,
ROCK or POP.
OPEN/CLOSE – to open and close the CD door
STANDBY – to switch the unit on and off
STANDBY 6 – goes out when the unit is on CD
(FUNCTION switch in position CD)
REMOTE – to receive the remote signals
SENSOR ( only RR 760 CD) PLAY/PAUSE 2; – to start and interrupt
playback
Back panel
STOP 9
– to stop playback
Battery compartment: – for inserting 8 batteries
PROG. – to programme track numbers
type R20, UM1 or D-cells. in the memory
Back up battery compartment: – for inserting 2
R-SKIP Q – to skip and search
batteries type R6,UM-3 or AA-
backward
cells
F-SKIP R – to skip and search forward
AC MAINS – Socket for mains lead.
INTRO – to play only the first 10
seconds of each title
REPEAT – to repeat one/all tracks
RANDOM – to play the titles of a CD in
random order
Playing a CD
Searching for a passage during play
• Hold R-SKIP Q down to search backwards
to the beginning.
• Hold F-SKIP R down to search forwards to
the end.
Note: This function can be described as
'audibly' searching for a title.
During the search, volume is reduced and returns to
its adjusted level as soon as the button is released.
Random
• Press the RANDOM button.
– 'RANDOM' lights up on the display.
• Press PLAY/PAUSE 2;.
– The tracks are played in random order until all
of them have been played once.
• By pressing RANDOM during playback, random
play starts from the end of the playing track.
• The function is deactivated by pressing
STOP 9 (in which case the CD stops) or
RANDOM; in this case the remaining tracks
are played in their normal order.
• The random function is not possible during
playback of a programme.
Intro
• Press INTRO to play only the first 10 seconds
of each title.
– 'INTRO' lights up on the display.
After the last title, the CD player stops.
• The function is deactivated by pressing
STOP 9 (in which case the CD stops) or
INTRO; in this case the remaining tracks are
played back in the normal way.
CONTROLS
Display (illustration: RR 760 CD)
ANTENNA
CLASSIC ROCK POP
VOL
DIGITAL SOUND INTRO REPEAT RANDOM
CONTROL
CHTRACK MEMORY
OPEN/CLOSE
UP/
BAND F-SKIP STANDBY
STOP
REPEAT
STANDBY
DOWN/ CD/RADIO
R-SKIP
MEM PROG
The display indicates:
PLAY/
INTRO
PAUSE REMOTE
RANDOM
CLASSIC, ROCK, POP: the selected sound effect.
SENSOR
TAPE DIRECTION
TAPE:
B
;
INTRO:
REPEAT:
CASSETTE
Radio RANDOM:
(FUNCTION switch in position RADIO)
CH:
PROG. – to store the radio stations
TRACK:
DOWN Q – to tune backward
MEMORY:
UP R
– to tune forward
BAND – to select between FM, MW,
:
and LW waveband
MEM 34
– to select the next/previous
VOLUME:
memory position
Cassette
MW/FM/LW: indicates the selected waveband
(FUNCTION switch in position TAPE)
88
0
– to start recording
B
– to start cassette playback
8 8 : 8 . 8
Q
– fast rewind
R
– fast forward
MHz/kHz:
9//
– to stop and eject the cassette
;
– to interrupt and continue playback
and recording
CD PLAYER
Repeat
Repeating the CD
• By pressing REPEAT once, all tracks are
repeated.
REPEAT
– 'REPEAT' lights up; the CD will now be
TRACK
repeated continuously.
Repeating a track
• By pressing REPEAT twice, one track is
repeated.
– 'REPEAT' starts flashing; the actual track will
REPEAT
now be repeated continuously.
TRACK
• To switch the repeat mode off, press REPEAT
one more time, or press STOP 9.
Programming
RANDOM
TRACK
By programming the player you can play up to
20 tracks in any desired order. If you exceed the
maximum of 20 tracks, the programme function
will start again from the beginning.
Storing a programme
• In STOP mode, press PROG..
'MEMORY' and 'TRACK' start flashing.
• Select the first desired track using R-SKIP Q
TRACK MEMORY
or F-SKIP R.
• Store this track by pressing PROG. again.
• Select and store in this way all desired titles.
• Press PLAY/PAUSE 2; to start playback of the
programme.
Checking the programme
INTRO
• In STOP mode, press PROG. repeatedly: The
TRACK
display shows in sequence all programmed
track numbers.
• Press PLAY/PAUSE 2; to start playback of the
programme.
Radio aerials
– For FM, pull out the telescopic aerial. To
improve FM-reception, incline and turn the
TAPE
aerial.
Reduce its length if the FM-signal is too strong
VOLUME
(very close to a transmitter).
dB – For MW/LW, the set is provided with a built-
FM
in aerial, so the telescopic aerial is not
MW
MHz
LW kHz needed. Direct the aerial by turning the whole
set.
Radio reception
when cassette deck is selected • Set the FUNCTION switch to RADIO.
lights up during CD playback • Adjust the sound using the VOLUME, DSC and
lights up during the CD pause mode SURROUND SOUND controls.
lights up during the INTRO function • You may connect stereo headphones having a
3.5 mm plug to the jack
lights up = repeat all
– Inserting the plug will disconnect the speakers.
flashing = repeat one
• Select the wave band using the BAND button.
lights up during the RANDOM function
• Start the automatic station search by holding
indicates the radio memory channel
the UP 22 or DOWN 11 button down for one
indicates the CD track
or two seconds, and then releasing it.
programming or programme play-
– The tuner automatically searches for the next
back (CD) or storing stations (radio)
station with sufficient signal strength.
lights up when receiving FM stereo
• Repeat this step to search for other stations.
stations
• To tune to a weak station, briefly press the
(only RR 760 CD) lights up when
UP 22 or DOWN 11 buttons several times
adjusting the volume indicated in dB
until the correct frequency is displayed, or until
reception is best.
track number (CD) or memory – When ' ' appears on the display, you are
receiving an FM stereo transmitter.
channel (radio)
playing time (CD) or station
5:
frequency (radio)
for FM reception the frequencies
are indicated in MHz and for
MW/LW reception in kHz
CD PLAYER
Changing the programme
Adding tracks to the programme
• Press PROG. repeatedly until the display shows
the first empty memory location
(under TRACK appears 00).
• You can now add tracks to the sequence as
described above (up to 20).
Replacing previously programmed tracks
• Press PROG. repeatedly until the display shows
the step you wish to replace.
• Select the track you want to enter in its place.
• Store this track by pressing PROG..
Playing a programme
• Press PROG. once to show the first track of the
programme.
• Press PLAY/PAUSE 2;.
– Play starts with the first track of the programme.
– After the last track playback stops.
– The CD's total playing time and number of
tracks appear on the display.
Note:
• Press STOP 9 to stop playback.
• While playing a programme, it is possible to
use R-SKIP Q or F-SKIP R to select the
desired programmed tracks.
Erasing a programme
• To clear the programme, press the PROG.
button and afterwards STOP 9.
– You can only erase the programme when the
CD player is stopped.
• The programme is also erased:
– by opening the CD door using OPEN/CLOSE;
– if you move the FUNCTION selector;
– if the batteries are exhausted or if the power
supply is interrupted in another way.
RADIO
CH MEMORY
FM
MHz
CH
FM
MHz
p .
FM
MW
LW kHz
CH
LW kHz
FM
MHz
TRACK MEMORY
TRACK MEMORY
1
TRACK
1
Storing stations
You can store a maximum of 40 stations
(20 x FM, 10 x MW and 10 x LW).
• Select the wave band using the BAND button.
• Select the desired station with the UP 22 or
DOWN 11 buttons.
• Press the PROG. button.
– 'MEMORY' starts flashing on the display.
• Select within 5 seconds the channel you wish
to assign to this station with the MEM 3 or 4
buttons. If not, you will leave the function
without storing the station.
• While 'MEMORY' is flashing , press PROG. to
store this station.
– 'MEMORY' disappears from the display.
The display now indicates the station's
assigned channel, its frequency and
waveband.
• If you assign a station to a channel that had
been previously assigned to a different station,
the old station is deleted and replaced by the
new one.
Selecting stations
• Select the wave band using the BAND button.
• Select the desired memory channel with the
MEM 3 or 4 button.
– The display indicates the selected channel, the
station frequency and waveband.
Last station memory
LAST STATION MEMORY means that the unit
'remembers' the last frequency that was tuned to.
This function ensures that the station which was
selected before the radio was switched off is
automatically selected again when your radio is
switched back on.
CASSETTE DECK
Cassette recording
Recording from the CD player
(CD synchro recording)
• Set the FUNCTION switch to CD.
• It's not necessary to start the CD player sepa-
rately: by pressing 0 the CD player starts
automatically.
– If the CD player is in STOP position, recording
will start from the beginning of the CD (or from
the beginning of the programmed selection).
• To start a recording in the middle of a track,
play the CD in the normal way.
• As soon as the desired passage is reached,
pause the CD and then start recording by
pressing 0.
Recording from the radio
• Set the FUNCTION selector to RADIO.
• Select the wave band using the BAND button.
• Select the desired station with the UP 22 or
DOWN 11 buttons or with the MEM 3 or 4
buttons.
• Start recording by pressing 0.