Herunterladen Inhalt Inhalt Diese Seite drucken

Operation; Playback; Set The Power To Standby; When Using The Unit As A Power Amplifier - Pioneer A-50-K Bedienungsanleitung

Vorschau ausblenden Andere Handbücher für A-50-K:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 30

Operation

Chapter 4:
Operation

Playback

SACD/CD player
Network audio player
NETWORK AUDIO PLAYER
N-50
/I STANDBY/ON
FUNCTION
STANDBY
PURE AUDIO
Hi-Bit 32
iPod/USB
5V
2.1A
2
6
Playback
6
6
1
Turn on the power of the playback
component.
2
Turn power ON to the unit.
• If the unit is in the standby mode, press the remote
control's  STANDBY/ON button.
3
Select the source you want to playback.
Select the playback component.
• When using the front panel controls, rotate the
INPUT SELECTOR knob.
iPod dock, etc
Turntable
CD recorder or
iPod
Music>
Extras>
tape deck
Settings>
Shuffle Songs
Backlight
Tuner
MENU

Playback
5
3
• In the case of the A-70, if PHONO is selected, use
the CARTRIDGE select switch to designate the type
of cartridge used with your turntable, either MM
() or MC ().
4
Start playback of the component you
selected in step 1.
5
Adjust playback volume with VOLUME
control.
VOLUME
6
Adjust the tone to your preference using
the BASS and TREBLE controls, and
LOUDNESS button.
If the DIRECT button has been set to ON, these controls
are disabled.

Set the power to Standby

1
Press the remote control's  STANDBY/
ON button.
The next time you wish to turn on the power, press the
remote control's  STANDBY/ON button.
• If the front panel's /I STANDBY/ON button is
pressed, the power will be turned off. In this case, if
the power is off, pressing the remote control's
 STANDBY/ON button will not turn on the power.
To turn on the power again, press the front panel's
/I STANDBY/ON button.

When using the unit as a power amplifier

When a pre-amplifier is connected to the unit's POWER
AMP DIRECT IN terminals, the unit can be used as a
power amplifier.
1
Press the POWER AMP DIRECT button
on the front panel of the unit.
The POWER AMP DIRECT indicator will light.
Caution
• When the POWER AMP DIRECT indicator is
lighted, operations change as follows:
– The unit's front-panel VOLUME, BASS, TREBLE,
and BALANCE controls are disabled. These
adjustments are controlled by the component
connected to the unit's POWER AMP DIRECT IN
terminals.
– The LOUDNESS button and ATTENUATOR
button (A-70 only) are disabled.
– When the POWER AMP DIRECT indicator is
lighted, sound volume from the unit will
automatically be fixed at its maximum output.
When using this unit as a power amplifier,
check the output level of the component
connected to the POWER AMP DIRECT IN
terminals and set it to a low level as appropriate
before turning on the POWER AMP DIRECT
indicator. If the sound volume of the component
connected to the POWER AMP DIRECT IN
terminals is initially set to a high output level,
loud sound may suddenly be output when the
POWER AMP DIRECT indicator lights.
– Sound is not produced from the PHONES jack
and RECORDER OUT terminals.
• For more information, consult the operating
instructions for the component connected to the
unit's POWER AMP DIRECT IN terminals.
04
11
En

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

A-50-sA-70-sA-70-kA-50

Inhaltsverzeichnis