Putting Into Service; Noise Development - BOMANN VL 1133 S CB Bedienungsanleitung


NOTE:
There may still be dust or production residues on the surface
of the device. We recommend that you quickly wipe off the
housing with a damp cloth.
Assembly instructions
The device must be completely assembled before use! While
reading the text it is advisable to refer to the „Overview of the
Components".
1. Place the parts of the base together in the shape of a cross.
2. Screw the mounting plate (13) tightly to the base. For this
you should use the four crosshead screws and washers
supplied.
3. If necessary, remove the height adjustment nut (9). Push
the covering cap (10) on to the lowest position of the upright
tube (11). Screw the height adjustment nut back on to the
upright tube (11).
4. Loosen the connection screw (8) and insert the gear casing
(7) and the motor casing (5) on the stand tube. Then tighten
the crosshead screw with a screwdriver so that it is hand-
tight.
5. Unscrew the mounting ring (18) in an anticlockwise direc-
tion. Keep it ready to hand.
6. Position the rear protection grid (16) in place in accordance
with the recesses.

NOTE:
Please ensure that the carrying handle is facing upwards.
7. Turn the attachment ring (18) for the rear protection grid (16)
slightly in a clockwise direction.
8. Attach the propeller. Note the position of the guide pin on the
motor shaft.
9. Tighten the attachment screw (19) for the propeller in an
anticlockwise direction.
10. Remove the preassembled fastening screw (1) and nut (3)
from the wire mesh guard. Keep it ready to hand.
11. Insert the front wire mesh guard (20) into the hook (17) .

NOTE:
Ensure that the holes for the attachment screw in the front
and rear protective grille are aligned one above the
12. Secure the wire mesh guard with the fastening screw (1)
and nut (3).
13. Close the attachment hooks.
Position
The ideal position is a non-slip, flat surface.

Putting into Service

Electrical Connection
1. Before inserting the plug into the socket. Make sure that the
mains voltage to be used matches that of the device. You
can find this information on the nameplate.
2. Connect the device to a duly installed protective contact
socket.
05_VL 1133 S CB.indd 21
Basic Settings
Set the blower inclination angle before starting the device. You
can adjust the inclination angle by tipping the blower casing with
both hands.
CAUTION:
The inclination angle amounts to approx. 10°.
Operation
Use the pushbutton switches on the front to select the speed:
• 3
• 2
• 1
• 0
Shift to „0" to switch off the device.
Fan Setting
For this you have two possibilities:
Fixed
• Turn the device off.
• Pull out the adjustment knob.
• Hold the fan by the protective cage and turn it in the desired
direction.
Oscillating
• Press in the adjustment knob.
• The device swivels automatically within a range of approxi-
mately 90°.
• Pull the adjustment knob in order to switch the function off.
WARNING:
• Always remove the mains plug before cleaning the device.
• If you need to remove the safety guard: Always switch the
device off and remove the mains plug.
• Under no circumstances should you immerse the device
in water for cleaning purposes. Otherwise this might result
other. in an electric shock or fire.
CAUTION:
• Do not use a wire brush or any abrasive items.
• Do not use any acidic or abrasive detergents.
• Clean the outside of the device with a dry cloth without any
additives.
• If the device is very dirty wet a cloth with water and then
wipe the device dry once you have finished.

Noise development

The workplace-related emission value is less than 70 dB(A).
Use
fast
medium
slow
off
Cleaning
08.11.11 11:23
21