Fluval G3 Kurzanleitung Seite 5

MENU SETTINGS
7. 6.
8.
ESC
9.
1.
2.
3.
MAIN MENU
1.MECH: Shows the elapsed days 4.SCROLL UP/DOWN:
from last recorded maintenance Both keys allow you to scroll to
operation of the mechanical and through menu choices as well
fi ltration cartridge. as and increasing and decreasing
values.
2.CHEM: Shows the elapsed days
from last recorded chemical 5.WATER FLOW: Displays the
cartridge maintenance operation. approximate fl ow rate. When a
100% fl ow is detected the triangle
3.BIOL: Shows the elapsed weeks will be full and water will move
from last recorded biological through the tubes. When the fl ow
maintenance operation. rate decreases, the triangle will
empty accordingly.
GLOBAL and OPERATIONAL SETTINGS MENUS
1. To reach either menu from the Main Menu, use the scroll keys.
2. When the desired Menu is displayed, press "Enter" to scroll through the available
options within same Menu.
3. When the desired option is highlighted, press "Enter" to open its specifi c sub-screen.
"GLOBAL SETTINGS" MENU
This menu allows you to set the options of:
Display language, Screen contrast, Temperature
scale, Dimmer delay and Default setting.
To access the global settings menu press the scroll
key up or down.
8 H Y D R O T E C H P E R F O R M A N C E M O N I T O R | A D VA N C E D F I LT R AT I O N S Y S T E M
EN.
5. Start up Screen
When the fi lter is fi rst turned on the welcome screens
will be displayed with the messages "Fluval G3 / G6"
"Language Selection" then "initializing." When the
language screen is displayed (English is the default
setting) other language choices can be made ( French
(FR), German (D), Spanish (ES), Italian (IT). To chose an
4.
alternate language use the scroll keys to move to the
selected language. Press Enter to register the
language. If no language is chosen, the fi lter will move
to the default English setting. See the section on
Global Settings for more information.
6.T°C: Displays the aquarium 8.ESCAPE KEY: Repeatedly
water temperature measured. pressing the "ESC" key brings you
If electrical supply is 50Hz the back to the main screen.
temperature is automatically set
to Celsius degrees (°C), if the 9.ENTER KEY: This key confi rms
electrical supply is 60Hz, the and then sets the information
temperature is set to Fahrenheit entered. If you press the "ESC" key
degrees (°F). without having fi rst pressed the
"ENTER" key to confi rm your data
7.EC _S/cm: Displays the value will not be saved.
of water electrical conductivity
monitored by the fi lter by automati-
cally distinguishing if it's a marine
or fresh water aquarium. Allow
48 hrs for proper calibration.
To set any options from this menu including options
on the submenus, use the following procedure:
• Press "Enter" to access the menu.
• Use the scroll keys to highlight the desired
selection.
• Press "Enter" to enter the sub-screen
• ONLY In "Set Contrast" Press "Enter" again to
activate the scroll keys (The value option will start
to fl ash)
• Use the scroll keys to change values.
• Press "Enter" to register the selection.
• If no button is pressed, the screen returns to the
main screen after 3 minutes.
• Continuous pressing of the "ESC" key will bring you
back to the main screen
"OPERATIONAL SETTINGS" MENU
Within this menu you can set "Temperature and
Conductivity Alarm Points" as well as "Mechanical,
Chemical and Biological maintenance schedules".
To access the "Operational Settings" menu press the
scroll keys up or down.
TEMPERATURE POINTS
The following options are available:
Water Temp: Displays the aquarium water
temperature.
Alert: Turns "ON / OFF" the "Alert Temperature,
out of range" message. When water temperature
goes out of the set temperature range, the T°C line
on the main screen will fl ash.
Min/Max: Sets the min/max values for the water
temperature range. The minimum temperature can't
be higher than the maximum and vice versa.
CONDUCTIVITY POINTS
The following options are available:
Conduct: Displays the water conductivity value.
Find more information on conductivity on
www fl uval-g.com.
Salinity: Displays water salinity in PSU. Salinity only
appears if water is marine
Alert: Turns "ON / OFF "Alert Conductivity, out of
range" message. When conductivity goes out of
range the EC line on the main screen will fl ash.
Min/Max: Sets the min/max values for the water
conductivity range. The minimum conductivity can't
be higher than the maximum and vice versa.
MECHANICAL SCHEDULE
The following options are available:
Elapsed Days: Counts the days elapsed since the
last recorded maintenance. This information is
displayed on the "MECH" line on the main menu. To
reset to zero use the scroll keys to select the value,
press enter to choose the option, use the scroll key
to choose "YES" and press "Enter".
To set any options from this menu including options
on the submenus, use the following procedure:
• Press "Enter" to access the menu.
• Use the scroll keys to highlight the desired
selection.
• Press "Enter" to enter the sub-screen.
• Use the scroll keys to highlight the adjustable
value.
• Press "Enter" (The value will start to fl ash)
• Adjust the value with the scroll keys
• Press "Enter" to register the selection.
• If no button is pressed, then after 3 minutes the
screen returns to the main screen.
• Continuous pressing of the "ESC" key will bring you
back to the main screen
Alert: Turns the warning message for "Mech"
maintenance alert "ON or OFF".
Days to alert: Use the scroll keys to choose the
days between the previous and next maintenance.
The highest number available is 99.
CHEMICAL SCHEDULE
The following options are available:
Elapsed Days: Counts the days elapsed since the
last recorded chemical maintenance. This
information is displayed on the "CHEM" line on the
main menu. To reset to zero use scroll keys to select
the value, press enter to choose the option, use the
scroll key to choose "YES" and press "Enter".
Alert: Turns the warning message for "Chem"
maintenance alert "ON or OFF".
Days to alert: Use the scroll keys to choose the
days between the previous and next maintenance.
The highest number is 99.
BIOLOGICAL SCHEDULE
The following options are available:
Elapsed Weeks: Counts the weeks elapsed since
the last recorded biological maintenance. This
information is displayed on the "Biol" line on the
main menu. To reset to zero use scroll keys to
select the value, press "Enter" to choose the option,
use the scroll key to choose "YES" and press "Enter".
Alert: Turns the warning message for "Bio"
maintenance alert "ON or OFF"
Weeks to alert: Use the scroll keys to choose the
weeks between the previous and next maintenance.
The highest number is 99.
Q U I C K S TA R T G U I D E 9
EN.