Safety; Settings; Cleaning, Care And Maintenance; Troubleshooting - AEG THERMO BODENTBS TB 50 160/1-8 Bedienung Und Installation

Operation – for users and qualified contractors
1.2 Other symbols in this documentation
Note
General information is identified by the adjacent
symbol.
» Read these texts carefully.
Symbol Meaning
Material losses
!
(appliance damage, consequential losses and envi-
ronmental pollution)
Appliance disposal
» This symbol indicates that you have to do something.
The action you need to take is described step by
step.
1.3 Information on the appliance
Symbol Meaning
Underfloor heating system (direct action)
1.4 Units of measurement
Note
All measurements are given in mm unless stated
otherwise.

2. Safety

2.1 Intended use
The heating mat provides direct underfloor heating and
is used for electric underfloor heating in individual areas,
e.g. bathrooms, kitchens, sauna lobbies, hallways or other
living areas and in indoor swimming pools and other wet
rooms.
This appliance is intended for domestic use. It can be
used safely by untrained persons. The appliance can also
be used in a non-domestic environment, e.g. in a small
business, as long as it is used in the same way.
Any other use beyond that described shall be deemed
inappropriate. Observation of these instructions and of
instructions for any accessories used is also part of the
correct use of this appliance.
2.2 General safety instructions
WARNING Injury
!
The appliance may be used by children aged 8 and
up and persons with reduced physical, sensory or
mental capabilities or a lack of experience and know-
how, provided that they are supervised or they have
been instructed on how to use the appliance safely
and have understood the resulting risks. Children
must never play with the appliance. Children must
never clean the appliance or perform user mainte-
nance unless they are supervised.
Material losses
!
Only operate the heating mat when fully installed
and with all safety equipment fitted.
16
2.3 CE designation
The CE designation shows that the appliance meets all
essential requirements according to the:
◦ Electromagnetic Compatibility Directive
◦ Low Voltage Directive
2.4 Test symbols
See type plate label, label on the warranty card or in the
main junction box.

3. Settings

You can set the required floor temperature by means of
an external temperature controller.
The floor temperature which can be achieved depends
on the floor structure and the floor covering. Observe the
information in the operating and installation instructions
for the temperature controller.
3.4.1 Temperature controller with time switch
Energy saving operation is ensured by installing a tem-
perature controller with time switch.
Using a temperature controller with time switch means
that you can adapt the heating operation to your lifestyle
by specifying when the heating mat will switch on and off.
» Adjust the operating times so that it switches on a
certain amount of time before use. The necessary
time depends on the floor structure and the floor
covering.
» Adjust the time it switches off so that the appliance
switches off approximately half an hour before the
end of use.
Further information can be found in the operating and
installation instructions for the temperature controller.
4. Cleaning, care and
maintenance
The heating mat does not require any particular main-
tenance.

5. Troubleshooting

Problem Cause
The heating mat does The temperature
not provide the neces- controller is not set
sary heating output. correctly.
For temperature con-
trollers with a time
switch: Operating
times are not set cor-
rectly.
There is no power.
If you cannot remedy the fault, notify your qualified con-
tractor. To facilitate and speed up your request, provide
the number from the type plate (000000-0000-000000).
You will find the type plate on the warranty card in these
instructions and in the main junction box.
Remedy
Adjust the tempera-
ture controller to the
maximum heating
level. After waiting for
a short time, check
whether the floor is
warming up.
Check the time switch
operating times and
adjust if necessary.
Check whether the
fuses/MCBs in your
fuse box have blown/
responded. If the
fuses/MCBs blow/
respond repeatedly,
notify your heating
contractor.