Werbung
A slight production of noise at the bearing of the centrifugal mass
is due to the construction and has no negative effect upon ope-
ration. Possibly occurring noise during reverse pedalling result from
engineering and are absolutely safe.
Do not use corrosive or abrasive materials to clean the equipment.
Ensure that such materials are not allowed to pollute the envi-
ronment.
The exercise cycle has a brake system, which require little main-
tenance and does not require any adjusting work.
Instructions for Assembly
Ensure that you have received all the parts required (see check
list) and that they are undamaged. Should you have any cause
for complaint, please contact your KETTLER dealer.
Before assembling the equipment, study the drawings carefully
and carry out the operations in the order shown by the dia-
grams. The correct sequence is given in capital letters.
The equipment must be assembled with due care by an adult
person. If in doubt call upon the help of a second person, if pos-
sible technically talented.
Please note that there is always a danger of injury when working
with tools or doing manual work. Therefore please be careful when
assembling this machine.
Ensure that your working area is free of possible sources of
danger, for example don't leave any tools lying around. Always
dispose packaging material in such a way that it may not cause
any danger. There is always a risk of suffocation if children play
with plastic bags!
List of spare parts
When ordering spare parts, always state the full article number,
spare-part number, the quantity required and the inspection number
stamped on the back.
Example order: Art. no. 7946 - 500 / spare-part no. 10100030/
2 pieces / inspection no .................... Please keep original pack-
aging of this article, so that it may be used for transport at a later
date, if necessary
Instructions de montage
F
Lire attentivement les présentes instructions avant le montage et la première utilisation de l'appareil. Elles contiennent des
renseignements importants relatifs à la sécurité des personnes ainsi qu'à l'emploi et à l'entretien de la bicyclette d´áppar-
tement . Conserver soigneusement lesdites instructions pour d'éventuels renseignements ainsi que pour effectuer l'entretien
de l'appareil ou commander des pièces de rechange.
Pour votre sécurité
La bicyclette pour la mise en forme, ne doit être utilisée que pour
les fins auxquelles elle est destinée, c'est-à-dire pour l'entraî-
nement des adultes.
Tout autre emploi est interdit, voire dangereux. Le fabricant ne
pourra être rendu responsable de dommages causés par l'emploi
inadéquat de l'appareil.
Vous vous entraînez avec un appareil dont la technique et la
sécurité correspondent aux exigences modernes. Les sources
possibles de danger qui pourraient entraîner des blessures ont
été soit supprimées, soit sécurisées.
Les réparations inadéquates et les modifications apportées à la
4
To operate correctly, the pulse function requires a minimum
voltage of 2,7 volts.
The hometrainer is dependent of revolutions per minute.
Please ensure that liquids or perspiration never enter the machine
or the electronics.
Before use, always check all screws and plug-in connections as
well as respective safety devices fit correctly.
The fastening material required for each assembly step is shown
in the diagram inset. Use the fastening material exactly as
instructed. The required tools are supplied with the equipment.
Bolt all the parts together loosely at first, and check that they have
been assembled correctly. Tighten the locknuts by hand until
resistance is felt, then use spanner to finally tighten nuts completely
against resistance (locking device). Then check that all screw
connections have been tightened firmly. Attention: once locknuts
have been unscrewed they no longer function correctly (the
locking device is destroyed), and must be replaced.
To pull off the pedal arms remove cap and screw (A). Grip the
pedal arm tightly, and screw in an M12 bolt (not supplied) into
the thread (B). After a few turns you may take off the pedal arm
(C).
For technical reasons, we reserve the right to carry out preliminary
assembly work (e.g. addition of tubing plugs).
Important: spare part prices do not include fastening material; if
fastening material (bolts, nuts, washers etc.) is required, this should
be clearly stated on the order by adding the words „with fastening
material".
KETTLER (GB) Ltd. · Merse Road · North Moons Moat ·
Redditch, Worcestershire B98 9HL · Great Britain
KETTLER International Inc. · 1355, P. B. 2747 · Virginia Beach ·
VA 23450 USA
http://www.kettler.net
construction de l'appareil (démontage des pièces d'origine,
montage de pièces non autorisées, etc.) peuvent entraîner des
risques imprévus pour l'utilisateur.
Les composants endommagés peuvent affecter votre sécurité et
la durée de vie de l'appareil. On remplacera donc sans tarder
les composants usés ou endommagés et on interdira l'emploi de
l'appareil aussi longtemps qu'ils n'auront pas été remplacés.
N'utiliser que des pièces de rechange KETTLER d'origine.
On cas de doute, on est prié de s'adresser à son concessionnaire
KETTLER.
En cas d'entraînement régulier et intensif, il y a lieu de contrôler,
Werbung
