Rinse Aid And Refined Salt; Loading The Rinse Aid; Loading The Refined Salt - Scholtes lvx 12-46 Bedienungsanleitung

Rinse aid and refined salt

 Only use products that have been specifically
designed for dishwashers.
Do not use table salt or industrial salt.
 If using a multi-functional product (2-in-1, 3-in-1, 4-
in-1, etc..) it is not necessary to add rinse aid;
however, we recommend that you add salt,
especially if you live in an area where the water is
hard or very hard. If you do not add salt or rinse
aid, the LOW SALT* and LOW RINSE AID* indicator
lights will flash continuously.

Loading the rinse aid

Rinse aid makes it easier for the crockery to dry,
as water runs off surfaces more readily and
therefore does not leave streaks or marks.
The rinse aid dispenser should be filled:
• whenever the indicator light (H) signals that it is
empty. Illuminated light: add rinse aid; unlit
light: there is no shortage of rinse aid in the
dispenser.
• when the LOW RINSE AID* indicator light on the
panel flashes;
H
F
G
Adjusting the amount of rinse aid
If you are not completely satisfied with the
washing or drying results, you may adjust the
quantity of rinse aid used. Use a screwdriver to
turn the dosage adjuster to one of the 6 pre-set
positions (the default position is set to 4):
• if there are white streaks on the crockery, set
the adjuster to a lower number (1-3).
• if drops of water remain on the crockery or there
are limescale marks present after the cycle has
finished, set the adjuster to a higher number (4-
6).
 If you are using multi-functional tablets (2-in-1, 3-
in-1, 4-in-1, etc..) and you wish to further improve
the drying performance of the appliance, fill the
dispenser and set the dosage adjuster to 2.

Loading the refined salt

In order to obtain the best possible results from a
wash cycle, make sure that the dispenser is never
empty. Refined salt removes limescale from the
water, thus avoiding the formation of deposits on
crockery. The salt dispenser is located in the
lower part of the dishwasher ( see Description ) and
1. Open the dispenser by
turning the lid (G) in an
anticlockwise direction.
2. Pour in the rinse aid,
making sure it does not
overflow from the
dispenser. If this happens,
clean the spill immediately
with a sponge.
3. Screw the lid back on.
should be filled:
• when the green float* cannot be seen by simply
looking at the cap of the salt dispenser;
• when the LOW SALT* indicator light on the
panel flashes;
• if your machine is not equipped with an
indicator light or a green float:
approximately every 30 wash cycles;
1. Remove the lower rack
and unscrew the cap of the
dispenser (in an anti-
clockwise direction).
2. For the first wash cycle
only: fill the dispenser up to
the edges with water.
3. Position the funnel
provided correctly ( see figure ) and fill the salt
dispenser up to the edges (approximately 2 kg); it
is normal for a little water to leak out.
4. Remove the funnel, wipe away any salt residue
from the thread and screw the cap on tightly, so
that detergent does not leak into the dispenser
during the wash cycle (this could damage the
water softening system beyond repair).
 When salt has been added, run a wash cycle
immediately, without crockery, in order to remove
any salt solution that has leaked out and to avoid
corrosion.
Adjusting the amount of salt*
It is possible to adjust the amount of salt used
according to the hardness of the water in your
area (this information is available from your local
water board).
1. Unscrew the dispenser cap.
2. Turn the arrow on the neck of
the dispenser ( see figure ) towards
the + or - symbols, using the table
below as a guide.
The default setting of the water softening system is
+.
- If using multi-functional tablets (2-in-1, 3-in-1, 4-in-
1, etc...) fill the salt dispenser and set the adjuster
to -; if the hardness of the water is greater than
60°fH, set it to +.
* Only available in selected models.
EN
19