Herunterladen Diese Seite drucken

Werbung

3-776-703-13(1)
Electret Condenser
Microphone
Operating Instructions
Mode d'emploi
Bedienungsanleitung
ECM-44B
Sony Corporation  2003
Printed in Japan
Frequency response
Réponse en fréquence
Frequenzgang
+20
+10
0
–10
–20
20
50
500
100 200
1k
2k
5k
Frequency in Hz
Fréquence en Hz
Frequenz in Hz
Directivity
Directivité
Richtwirkung
English
Before operating the unit, please read this manual
thoroughly. This manual should be retained for future
reference.
For the customers in Europe
This product with the CE marking complies with the EMC
Directive issued by the Commission of the European
Community.
Compliance with this directive implies conformity to the
following European standards:
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following
Electromagnetic Environments: E1 (residential), E2
(commercial and light industrial), E3 (urban outdoors),
E4 (controlled EMC environment, ex. TV studio).
The manufacturer of this product is Sony Corporation, 1-
7-1 Konan, Minato-ku, Tokyo, Japan.
The Authorized Representative for EMC and product
safety is Sony Deutschland GmbH, Hedelfinger Strasse
61, 70327 Stuttgart, Germany. For any service or
guarantee matters please refer to the addresses given in
separate service or guarantee documents.
Attention:
The electromagnetic fields at the specific frequencies
may degrade the intended performance level of analog
audio signals.
FEATURES
• Omni-directional characteristics with wide frequency
range (40–15,000 Hz)
• Powering system using an internal battery.
• Ideal design for professional application in radio and TV
studios or other audio fields because of its high quality
performance and its extremely compact size.
• Easy handling carrying case.
PRECAUTIONS
• The microphone should never be dropped or subjected
to any excessive shock.
• Keep the microphone away from extremely high
temperatures (above 60°C or 140°F)
• If the microphone is placed too near the speakers, a
howling effect (acoustic feedback) may occur. In this
case, decrease the speaker volume until the howling
stops.
• Microphone and recording instruments should be turned
on 10 minutes before they are actually used. This
assures stable performance of the microphones and
instruments.
PARTS IDENTIFICATION
Microphone capsule
Power supply section
Supplied accessories
Wind screen
Microphone holder
BATTERY OPERATION
1 Open the battery compartment by turning the sleeve
counterclockwise.
2 Insert an IEC designation R6 or LR6 (size AA) battery
10k
into the battery compartment.
20k
Check for correct polarity.
3 Close the compartment by turning the sleeve clockwise.
Be sure to close the sleeve firmly, otherwise
malfunction or noise may occur due to the loose fit.
Notes
• If the microphone is not to be used for a long time,
remove the battery to avoid any possibility of corrosion.
• In case of battery leakage, wipe off any deposit in the
battery compartment.
• Battery life depends on the battery type being used.
Refer to the "Battery life" in "Specifications" below.
When the battery is exhausted, sensitivity will be
decreased and distortion will be heard. When this
occurs, replace with a new battery.
CONNECTIONS
The output connector of the microphone is the Cannon
XLR-3-12C type. Connect the microphone plug to the
microphone input of a mixer or a tape recorder. The
microphone cable is 3m (10 feet) long.
If a longer cable is necessary, an extention cable up to
200 m (660 feet) may be used without affecting sound
quality or performance. Use a cable with a Cannon XLR-
3-11C connector at one end and an appropriate plug at
the other end which matches the input equipment.
Note
If cable connector connection is necessary, note that
there are two basic types connections, balanced to
ground and unbalanced to ground, and solder
connections carefully. Poor soldering may cause hum pick
up.
MORE ABOUT MICROPHONE USE
• To eliminate the effect of wind or breath noise, cover
the microphone with the supplied wind screen. This will
attenuate wind or breath noise by 14 dB.
• The supplied microphone holder is convenient for
attaching the microphone to clothing. Be careful not to
cover the microphone head.
• Attach the microphone with cellophane or vinyltape to
the inside of an instrument such as a guitar, bass, etc.,
to obtain a high quality sound. Be sure to place a rubber
or felt cushion between the microphone and instrument.
SPECIFICATIONS
General
Type
Electret condenser microphone
Power supply IEC designation R6 or LR6 battery (size
AA)
Microphone output terminal
Cannon XLR-3-12C type
Microphone cable
Approx. 2.3 mm dia., 3 m long (
dia., 10 feet long)
Microphone: Approx. 8.5 mm dia. × 14.5
Dimensions
dia. ×
mm (
11
/
19
32
Power supply section: Approx. 20 mm
dia. ×126 mm (
13
/
Mass
Microphone: Approx. 2 g (0.07 oz)
Power supply section: Approx. 119 g (4.2
oz) (including cable, not including battery)
Finish
Non-reflective black finish (microphone
capsule section)
Satin-nickel finish (power supply section)
Supplied accessories
Carrying case (1)
Microphone holder (1)
Wind screen (1)
Operating Instructions (1)
Warranty booklet (1)
Performance
Frequency range
Output
40–15,000 Hz
connector
Directivity
Omni-directional
Output impedance
250 ohms ±20% (1 kHz), balanced
Sensitivity (deviation ±3 dB)
Open circuit voltage:
–53 dB (2.2 mV, 0 dB = 1 V/1 Pa, 1 kHz)
Effective output level:
–49.8 dBm (0 dBm = 1 mW/1 Pa, 1kHz)
Recommended load impedance is more
than 3 kohms.
Signal-to-noise ratio
More than 62 dB (1 kHz, 1 Pa)
Inherent noise Less than 32 dB SPL (0 dB = 20µPa)
1
Wind noise*
Less than 40 dB SPL (with wind screen)
Induction noise from external magnetic field*
Less than 5 dB SPL/1 × 10
Maximum input sound pressure level (1 kHz, 1%)*
122 dB SPL (25.1 Pa)
Dynamic range
More than 90 dB
Environmental temperatures
–20°C to +60°C (–4°F to 140°F) for
storage
0°C to 60°C (+32°F to 140°F) for
operation
*1 Wind noise is the value measured by applying a wind
velocity of 2 m/sec. (6.6 ft./sec.) from all directions to
the microphone. The mean value is taken and
converted to the equivalent input sound level.
0 dB SPL = 20µPa
*2 The external magnetic field induction noise is
measured with the microphone placed in an alternating
magnetic field of 50 Hz, 1 milligauss.
0 dB SPL = 20µPa
*3 The maximum noise value is taken and then converted
to the equivalent input sound level.
0 dB SPL = 20µPa
Power requirements
Normal operating voltage
1.5 V DC
Minimum operating voltage
1.1 V DC
Current drain Less than 0.2 mA (1.5 V DC)
Battery life
R6 manganese battery: Approx. 5,000
hours
LR6 alkaline battery: Approx. 6,000 hours
Design and specifications subject to change without
notice.
Note
Always verify that the unit is operating properly before
use. SONY WILL NOT BE LIABLE FOR DAMAGES
OF ANY KIND INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT ON
ACCOUNT OF THE LOSS OF PRESENT OR
PROSPECTIVE PROFITS DUE TO FAILURE OF
THIS UNIT, EITHER DURING THE WARRANTY
PERIOD OR AFTER EXPIRATION OF THE
WARRANTY, OR FOR ANY OTHER REASON
WHATSOEVER.
Français
Avant la mise en service de l'appareil, lire attentivement
ce mode d'emploi et le conserver pour toute référence
ulterieure.
Pour les clients en Europe
Ce produit portant la marque CE est conforme à la
Directive sur la compatibilité électromagnétique (EMC)
3
/
inch
32
émise par la Commission de la Communauté
européenne.
La conformité à cette directive implique la conformité aux
/
inches)
32
normes européennes suivantes :
• EN55103-1 : Interférences électromagnétiques
dia. × 5 inches)
16
(émission)
• EN55103-2 : Sensibilité électromagnétique (immunité)
Ce produit est prévu pour être utilisé dans les
environnements électromagnétiques suivants : E1
(résidentiel), E2 (commercial et industrie légère), E3
(urbain extérieur) et E4 (environnement EMC contrôlé, ex.
studio de télévision).
Le fabricant de ce produit est Sony Corporation, 1-7-1
Konan, Minato-ku, Tokyo, Japon.
Le représentant autorisé pour EMC et la sécurité des
produits est Sony Deutschland GmbH, Hedelfinger
Strasse 61, 70327 Stuttgart, Allemagne. Pour toute
question concernant le service ou la garantie, veuillez
consulter les adresses indiquées dans les documents de
service ou de garantie séparés.
Attention:
Les champs électromagnétiques à fréquences
spécifiques peuvent dégrader le niveau de performance
prévu des signaux audio analogiques.
CARACTERISTIQUES
• Caractéristiques omni-directionnelles avec large
gamme de fréquences (40–15.000 Hz).
• Alimentation: soit par batterie interne.
• Conception idéale pour les travaux professionnels en
studio de radio ou de télévision et autres applications
audio en raison de ses performances de haute qualité
et de sa remarquable compacité.
• Etui de transport très pratique.
2
-7
T
PRECAUTIONS
3
• Ne jamais laisser tomber le microphone ni le soumettre
à des chocs.
• Tenir le microphone à l'écart de toute source de
température élevée (au-dessus de 60°C ou de 140°F).
• Si le microphone est placé trop près des enceintes, une
réaction acoustique (hurlement) se produira. Dans ce
cas, réduire le volume des enceintes de manière à
supprimer ce phénomène.
• Le microphone et les appareils d'enregistrement doivent
être mis sous tension 10 minutes avant leur utilisation
proprement dite afin d'assurer la stabilité de leur
fonctionnement.
IDENTIFICATION DES ELEMENTS
Accessoires fournis
Paravent
Pinces de microphone
FONCTIONNEMENT SUR PILE
1 Ouvrir le logement pile en tournant la douille dans le
sens inverse des aiguilles d'une montre.
2 Installer une pile R6 ou LR6 selon la désignation IEC
(format AA) dans le logement.
3 Refermer le logement en tournant la douille dans le
sens des aiguilles d'une montre. Refermer
convenablement la douille; faute de quoi, une
défaillance ou des parasites se produiraient.
Remarques
• Si l'on prévoit de ne pas utiliser le microphone pendant
longtemps, en retirer la pile pour éviter toute possibilité
de corrosion.
• En cas de fuite d'électrolyte, essuyer convenablement
tout dépôt dans le logement.
• La durée de vie de la pile dépend de son type. Voir
"Autonomie de la pile" sous "Spécifications" ci-après.
Lorsque la pile est déchargée, sa sensibilité diminue et
le son est déformé. Dans ce cas, remplacer la pile par
une neuve.
Capsule de microphone
Section d'alimentation
Connecteur
de sortie
Respecter les polarités.
(à suivre)

Werbung

loading

Inhaltszusammenfassung für Sony ECM-44B

  • Seite 1 Satin-nickel finish (power supply section) studio de télévision). Supplied accessories Carrying case (1) Le fabricant de ce produit est Sony Corporation, 1-7-1 Microphone holder (1) Konan, Minato-ku, Tokyo, Japon. Wind screen (1) Le représentant autorisé pour EMC et la sécurité des...
  • Seite 2 E4 (kontrollierter EMV-Bereich, z.B. Fernsehstudio). passt. 1,1 V Gleichspannung Type Microphone condensateur à électret Der Hersteller dieses Produkts ist Sony Corporation, 1-7- Stromaufnahme Alimentation 1 pile de format AA (R6 ou LR6 selon la Hinweis 1 Konan, Minato-ku, Tokyo, Japan.