Inhaltsverzeichnis
Werbung
Selecting a satellite channel
1
Use the numeric keys on the remote control unit if
you wish to directly enter the number of the desired
programme position (multi-digit numbers must be
entered within 3 seconds).
2
Use the ] | keys on the remote control unit or
the
keys on the receiver to step through the
programme positions (when pressing and holding
down a key, the programme positions scroll at high
1
speed).
Stand-by
1
Use the
b
key on the remote control unit or the
key on the front panel of the receiver to switch the
receiver to stand-by.
1
2
Use the same keys to switch the receiver on from
stand-by with the last selected programme position
(last station memory).
3
Use the ] | keys on the remote control unit or
the
keys on the receiver to switch the receiver
on again from stand-by.
4
Using the remote control unit's numeric keypad,
you can also directly select the desired programme
position on A stand-by.
Locking the receiver
With the receiver lock option "
)
" in the "System
...
setup" menu, you can lock all receiver functions
(see description of "The basic settings menu" in the
"Settings" chapter at page 12).
2
Favourite programmes
To have a fast access to your favourite program-
mes, you can mark these programmes.
1
In normal mode, the ] | keys switch to the next
higher or next lower programme position.
In favourite mode, the ] | keys will only switch
to programme positions which have been marked
before as favourite programmes. Not marked pro-
gramme positions are skipped. The symbol "
(
"
appears in front of the programme position
number.
¢
Press the
key to toggle between normal and
1
T XT
favourite mode.
2
If you use the numeric keys to directly select a pro-
gramme position (also a favourite programme posi-
tion), or if you switch to stand-by, the favourite
3
mode is automatically de-activated.
To mark a programme as favourite programme,
select the corresponding programme position and
call up the "Programme position setup" menu. Then
select
the
"
(
"
option
in
the
menu
(see description of the "Programme position setup"
menu).
Sound mute
¢
Press the
key to mute and restore the sound.
As long as the sound is muted, the
symbol is dis-
played in the top right corner of the picture screen.
Status display
Press the
.
key to switch on the status display.
After a few seconds, the status display disappears
automatically.
&
A
300
11.494 GHZ
$
V–
7.02 MHZ
7.20 MHZ
~
PANDA
BW 1
16:35
SU
&
/
$
1:
2:
3:
4:
The display shows the time, the programme posi-
tion number and the settings made for this pro-
gramme position (for an explanation, see next
chapter).
As long as the status display is on, you can use the
...
keys to call up the menus.
Volume Control
Pressing one of the
x c
buttons displays the volu-
me control menu.
24
/ OK
The volume control is only effective on the "TV"
EURO-AV socket. It has no effect on the video
recorder (VCR) and decoder (DEC) EURO-AV
sockets.
With the
buttons, you can adjust a volume
x c
value between 0 and 31.
Press the
O
button to store the volume setting in
memory.
As long as the setting is not yet stored in memory,
pressing the
.
button will restore the old setting.
If neither the
nor the
O
button is pressed, the
.
menu is exited after a few seconds. The set value
remains valid until the receiver is switched to
standby. Then the old setting is recovered.
The status display
1
If you press the
.
key on the remote control unit
4
once, the status menu is briefly displayed on the
picture screen.
&
A
300
11.494 GHZ
$
V–
7.02 MHZ
7.20 MHZ
5
~
PANDA
BW 1
16:35
SU
6
&
/
$
1:
2:
3:
4:
Meaning of symbols:
&
TUNER A or B
A 300
300 = Programme position
number
11.494 GHZ
Satellite channel transmis-
sion frequency
$
V–A
LNC setting: polarization V/H,
22 kHz switching frequency
off (–)/on (~),
satellite selection A/B/C/D
7.02 MHZ 7.20 MHZ Left and right audio
frequency
~ PANDA
Deemphasis/noise suppres-
sion
Bandwidth (levels 1 to 4)
BW 1
16:35 MON
Time, Day
1:
2:
&
/
3:
4:
$
1
Key functions:
cancel status display instantly,
:
1:
open Timer menu,
&
open »Programme position
2:
setup« menu,
/
Open »Basic settings« menu
3:
4:
$
Open »LNC settings« menu
The time can be set in the Timer menu. The remain-
ing channel settings (transmission frequency, LNC
setup, audio settings) are made in the "Programme
position setup" menu.
The on-screen menu guide
Call up the status menu by pressing the
key. As
1
.
long as this menu is displayed, you can call up the
remaining four menus by means of the numeric
keys
... .
For a displayed menu, the following key functions
apply principally (these functions will not be
explained again in the menu descriptions).
2
If you do not wish the TV picture as background,
you can display a blue background by pressing the
¢
¢
key. Pressing the
key again restores the
T XT
T XT
TV picture as background.
3
When in a menu, use the ] | keys to move bet-
ween menu options.
A value which can be changed is flashing in the
menu (CURSOR). Change a value with the
x c
keys. Numeric values can be changed at fast speed
by pressing and holding down the
x c
keys.
In most cases, a direct entry of the value is also
possible.
Press the
O
key to save the changes made. This
automatically closes the corresponding menu and
briefly displays the status menu.
To exit a menu without saving, press the
.
key.
The changes made are undone and the status menu
is briefly displayed.
The Timer menu/video recordings
The Timer menu is provided for programming upto
four timer events in a 28 day period.
VCR recordings are only made from input B.
When a Timer is active, each event can be repeated
on a weekly or daily basis.
When a timer is active the only function available on
INPUT B is the STATUS screen and access to opti-
on 1- TIMER MENU. Input A is not affected by a
Timer
event.
Overview
Press the
.
key and then the
key.
On the picture screen appear the status menu and
then the Timer menu.
Check the time and correct it if necessary.
1
&
300
SU
WEEK 1
20:14
22:05
/X
16:37
SU
/ OK
Meaning of symbols:
1
Timer No (1-4)
&
A
300
Programme position number
DAY
Day of the week or daily
*
)
WEEK
Week
1-4 or weekly
Start time
20:14
Stop time
22:05
Timer on/off
/X
Time, Day
16:37
/ OK : exit menu without saving,
OK: save and exit menu.
*
)
week 1 = the current week.
Werbung
Inhaltsverzeichnis
