Interconnection Example 3-Channel-Mode: 1 X Stereo System And 1 X Mono Subwoofer Bridged - Hifonics X3-ZEUS Bedienungsanleitung

EXAMPLE 3-Channel Mode: 1 x Stereo System & 1 x Mono Subwoofer bridged
Speaker
left
1 – 8 Ohms
REM BATT +12V
GND
FUSE
e
OLYMPUS
13
4 x 125 W/4Ω
4 x 200 W/2Ω 021220
4 x 250 W/1Ω
POWER INPUT
Subwoofer
2 – 8 Ohm
INTERCONNECTION
• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables. If
a separate SUB OUT from your headunit is available, use this for the LINE INPUT CH3/4 on the amplifier.
• Connect the speakers with SPEAKER OUTPUT + CH 1 - and + CH 2 -, and the subwoofer with the
SPEAKER OUTPUT CH3/4 + Mono Bridged - of the amplifier.
• Ensure by any means, that the total impedance load channel (CH1 & CH2) is not lower than 1 ohms and the total impedance load of
the bridged mode (CH3 & CH4) is not lower than 2 ohms. Too low impedance cause high temperature and will shut down the
amplifier operation.
INPUT MODE SWITCH
• Attend the regarding notes on page 26.
CROSSOVER SETTINGS CH1/2 (STEREO SYSTEM)
• Attend the regarding notes on page 26.
BASS BOOST CONTROLLER CH1/2 (STEREO SYSTEM)
• The BASS BOOST controller must be turned to 0 dB position in this interconnecting example .
LEVER CONTROLLER CH1/2 (STEREO SYSTEM) & CH3/4 (SUBWOOFER)
• Attend the regarding notes on page 26.
CROSSOVER SETTINGS CH3/4 (SUBWOOFER)
• In the mono/subwoofer mode the X-OVER switch must set to the LP/BP position (Lowpass/Bandpass mode), thereby the higher
frequencies will be eliminated. The cut-off frequency ist adjustable with the LOW PASS controller and should be set between
60 to 100 Hz, depending on the size of the subwoofer.
• In the lowpass mode (LP/BP) the HIGH PASS controller works also as subsonicfilter, that eliminates the ultra-low, not hearable and
harmful frequencies to generate a bandpass signal (Bandpass mode). The subsonic frequency should be set between 15 to 50 Hz,
depending on the size of the subwoofer. NOTE: If this value is higher than the lowpass setting, no sound is hearable.
• Push the STEREO 12 dB / MONO 24 dB push button to position MONO 24 dB, thereby the slewrate of the lowpassfilter on CH3/4 will
be advanced to 24db/octave.
BASS BOOST CONTROLLER CH3/4 (SUBWOOFER)
• The BASS BOOST controller adjusts the bass enhancement between 0db and +18dB.
• A too high bass boost may cause clipping/distortion and damage on the loudspeakers and also may harm your hearing abilities.
Use this controller carefully!
BASS REMOTE CH3/4 (SUBWOOFER )
• The enclosed BASS REMOTE Controller adjusts the bass-level e.g. from the driver's seat of the Subwoofer on CH 3/4.
Please use only this enclosed bass remote controller and cable.
4-CHANNEL AMPLIFIER: X3-OLYMPUS
Speaker
right
1 – 8 Ohms
MONO BRIDGED
LOGO BADGE
– CH2 + – CH1 +
BLUE
WHITE
– CH4 + – CH3 +
MONO BRIDGED
SPEAKER OUTPUT
Connect the bass remote
controller and the
remote terminal on the amplifier
with the enclosed cable.
Connect the stereo RCA output (FL/FR & RL/RR opt.
SUB OUT) of the headunit with LINE INPUTS CH1/2 and
CH3/4 of the amplifier
CH1/2
LINE INPUTS
CH1 CH3
BALANCED
INPUTS
CH2 CH4
CH3/4
FL FR RR
25
27
POWER LINE OUTPUT
INPUT MODE CH1/2 CH1/2
SUMMED CH1/2/3/4
FULL RANGE
L
4CH 2CH LP/BP FULL HP
X-OVER MODE CH1/2
LOW PASS HIGH PASS LEVEL BASS BOOST REMOTE
PROTECT
CH3/4 CH3/4
STEREO 12dB R
MONO 24dB LP/BP FULL HP
X-OVER MODE CH3/4
LOW PASS HIGH PASS LEVEL BASS BOOST
Switch position CH1/2 = HP or FULL
Switch position CH3/4 = LP/BP
RL