Interconnection Example: 1-Channel Mode 1X Mono Subwoofer Bridged - Hifonics X3-ZEUS Bedienungsanleitung

2-CHANNEL AMPLIFIERS: X3-ZEUS / X3-COLOSSUS

INTERCONNECTION EXAMPLE: 1-Channel Mode 1x Mono Subwoofer bridged

REM BATT +12V
ZEUS
2 x 350 W/4Ω
2 x 600 W/2Ω
2 x 750 W/1Ω
FUSE
POWER INPUT
Subwoofer
2 – 8 Ohm
Connect the bass remote controller and the remote
terminal (REMOTE IN) on the amplifier with the enclosed cable.
INTERCONNECTION
• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables.
If your headunit is equipped with a additional subwoofer lineout (SUB OUT), it is recommended to use this lineout.
• Connect the subwoofer with the speaker outputs (SPEAKER OUTPUT + Mono bridged -) by using appropriate wires.
• Ensure by any means, that the total impedance load of the channel-pair is not lower than 2 ohms. Too low impedance cause high
temperature and will shut down the amplifier operation.
• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
CROSSOVER SETTINGS
• In the mono/subwoofer mode the X-OVER switch must set to the LP/BP position (Lowpass/Bandpass mode), thereby the higher
frequencies will be eliminated. The cut-off frequency ist adjustable with the LOW PASS controller and should be set between
60 to 100 Hz, depending on the size of the subwoofer.
• The HIGH PASS controller is in this interconnection example without function.
• The SUBSONIC controller eliminates the ultra-low, not hearable and harmful frequencies and generate a bandpass signal. The subsonic
frequency should be set between 15 to 50 Hz, depending on the size of the subwoofer.
NOTE: If this value is higher than the lowpass setting, no sound is hearable.
• Push the STEREO 12 dB / MONO 24 dB push button to position MONO 24 dB, thereby the slewrate of the lowpassfilter will be advanced
to 24db/octave.
LEVEL CONTROLLER
• Turn the LEVEL controller of the amplifier to the 9V position.
• Turn the volume controller of the headunit to 80 - 90% of its full setting.
• Turn the LEVEL controller clockwise until you hear some distortion.
• Then turn back the LEVEL controller slightly until you hear a cleaner sound.
BASS BOOST CONTROLLER
• The BASS BOOST controller adjusts the bass enhancement between 0db and +18dB.
• A too high bass boost may cause clipping/distortion and damage on the loudspeakers and also may harm your hearing abilities.
Use this controller carefully!
BASS REMOTE
• The enclosed BASS REMOTE Controller adjusts the bass-level e.g. from the driver's seat.
Please use only this enclosed bass remote controller and cable.
• Der REMOTE OUT port is suitable to connect the bass remote cable of an additional amplifier of the HiFONICS X3 Series (only in LOW
PASS-Mode). Thus to this, you are able to control two or more amplifiers with only one bass remote controller.
GND SPEAKER OUTPUT LOGO BADGE
BLUE
WHITE
LCH RCH
e
13
MONO BRIDGED
021224
output (R/L or SUB OUT)
of the headunit with LINE
INPUT R/L of the amplifier
LINE INPUT
L
SUBSONIC LOW PASS
R
BALANCED INPUT
Connect stereo RCA
R L
23
X-OVER MODE
POWER
LINE OUTPUT
STEREO 12dB PROTECT
MONO 24dB
HIGH PASS LEVEL BASS BOOST
VICE VERSA
LINE OUTPUT SIGNAL
REMOTE IN REMOTE OUT
Switch position LP
Switch position MONO 24 dB