Interconnection Example 4-Channel-Mode: 1 Stereo System (Front-System) And 1 X Stereo System (Rear-System) - Hifonics X3-ZEUS Bedienungsanleitung

INTERCONNECTION EXAMPLE: 4-Channel Mode 2 x Stereo System (Front & Rear)
Loudspeaker
front / left
1 – 8 Ohms
REM BATT +12V
GND
FUSE
e
OLYMPUS
13
4 x 125 W/4Ω
4 x 200 W/2Ω 021220
4 x 250 W/1Ω
POWER INPUT
Loudspeaker
rear / left
1 – 8 Ohms
INTERCONNECTION
• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables.
• Connect the front- and rear speakers with the speaker outputs (SPEAKER OUTPUT + 1CH -, + 2CH - and + 3CH -, + 4CH -).
• Ensure by any means, that the total impedance load of all speakers is not lower than 2 ohms. Too low impedance cause high temperature
and will shut down the amplifier operation.
• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
INPUT MODE SWITCH
• Select the 4CH position on the INPUT MODE switch. If there is only one RCA stereo audio cable from the headunit available, connect
the CH1/2 RCA line inputs and select the 2CH position.
CROSSOVER SETTINGS CH1/2 & CH3/4
• By using bigger speakers (more than 20cm) you can set the X-OVER switch to the FULL position (Full Range Signal).
• By using smaller speakers (8.7cm - 16cm) you must set the X-OVER switch to the HP Position (Highpass Mode) to avoid any damage
by lower frequencies on the speakers. The cut-off frequency is adjustable with the HIGH PASS controller and should be set between
60Hz to 150Hz, depending on the size of the speakers.
• The LOW PASS Controller is not in use in this interconnecting example.
LEVEL CONTROLLER CH1/2 & CH3/4
• Turn the LEVEL controller of the amplifier to the 9V position.
• Turn the volume controller of the headunit to 80 - 90% of its full setting.
• Turn the LEVEL controller clockwise until you hear some distortion.
• Then turn back the LEVEL controller slightly until you hear a cleaner sound.
BASS BOOST CONTROLLER
• The BASS BOOST controller must be turned to 0 dB position in this interconnecting example .
BASS REMOTE
• The enclosed BASS REMOTE Controller is not in use in this interconnecting example.
REFERENCE NOTE
Do not connect loudspeaker cables with the vehicle's chassis. Always ensure the correct polarity
of all connections. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
4-CHANNEL AMPLIFIER: X3-OLYMPUS
Loudspeaker
front / right
1 – 8 Ohms
MONO BRIDGED
LOGO BADGE
– CH2 + – CH1 +
BLUE
WHITE
– CH4 + – CH3 +
MONO BRIDGED
SPEAKER OUTPUT
Loudspeaker
rear / right
1 – 8 Ohms
Connect the stereo RCA output (FL/FR & RL/RR)
of the headunit with LINE INPUTS
CH1/2 and CH3/4 of the amplifier
CH1/2
LINE INPUTS
CH1 CH3
BALANCED
INPUTS
CH2 CH4
CH3/4
FL FR RR
26
POWER LINE OUTPUT
INPUT MODE CH1/2 CH1/2
SUMMED CH1/2/3/4
FULL RANGE
L
4CH 2CH LP/BP FULL HP
X-OVER MODE CH1/2
LOW PASS HIGH PASS LEVEL BASS BOOST REMOTE
PROTECT
CH3/4 CH3/4
STEREO 12dB R
MONO 24dB LP/BP FULL HP
X-OVER MODE CH3/4
LOW PASS HIGH PASS LEVEL BASS BOOST
Switch position CH1/2 = HP or FULL
and CH3/4 = HP or FULL
RL