Inhaltsverzeichnis
Werbung
Mounting and Operating Instructions
Style Variant 29011 / 29021 LED CG-S
3. Conformity with
Standards
Conforms to: EN 60 598-1, EN
60 598-2-22 and DIN EN 1838.
Developed, manufactured and
tested in accordance with DIN
EN ISO 9001.
4. Technical data
Input voltage: 230/240 V AC
50/60 Hz
176-275 VDC
Viewing distance: 32 m
Enclosure material:
Polycarbonat in grey
(850°C glow wire resistant)
Rated current:
29011
19 mA
29021
25 mA
Connection power mains
operation
29011
7.6 VA/4.4 W
29021
7.5 VA/5.8W
Insulation class:
II
Protection category acc. to
EN 60529:
IP 41
Admissible ambient
temperature:
-10°C...+40°C
Supply terminals 2,5 mm²
Weight:
29011:
1,1kg
29021:
1,2kg
Lamp: 29011
3 x 1.1 W LEDs
29021
4 x 1.1 W LEDs
4.2 Brief description/
Scope of application
The safety and exit luminaires
Style 29011,-021 LED CG-S are
suitable for operation on CEAG
emergency lighting systems acc.
to EN 50 172, DIN VDE 0100-718
and E DIN VDE 0108-100.
The advanced switching and
monitoring mode is only available
in combination with CEAG CG-S-
technology.
5.Installation
For the mounting and ope-
ration of electrical appara-
tus, the respective national
safety regulations as well as
the general rules of engineering
must be observed!
5.1 Assembly
Style Variant LED 29011
Loose the snap hooks of the le-
gend cover with a qualified slot-
headed screwdriver and lift the
cover from the enclosure. Loose
the 4 screws with a cross-slotted
screwdriver and lift the top part
of enclosure from the lower part.
According to assembly conditions
tweak out optional the impressed
cable entries sideways or on the
back-side. Enter the sealing stop-
per and stamp or cut out a hole
for the using cable diameter. If the
sealing lips are damaged, replace
the cable entries to maintain the
protection. Unused cable entries
which are tweaked out must be
closed with sealing stoppers (IP-
degree of protection).
Insert the cable in the body of the
lamp and attach it through the 4
holes in the corners of enclosure
to the wall or ceiling with appro-
priate screws.
Connect the mains cable to the
terminals of the module.
Put up the top part of enclosure
and fix it with the 4 screws.
Style Variant LED 29021
Loose the snap hooks of the
legend cover with a qualified
slot-headed screwdriver and lift
the cover from the enclosure.
Remove the lamp from the sok-
ket. Loose the snap hooks of
the trapeze shaped cover at the
entries- and mounting-side of the
luminaire. According to assembly
conditions close open cable ent-
ries with sealing stoppers and
stamp or cut out a hole.
Connect the mains cable to the
terminals of the module.
Put in the trapeze shaped cover
between the adjusted trapeze
shaped blocks of enclosure and
snap the 4 snap hooks.
Snap on the legend covers on the
enclosure of the luminaire.
5.2 LED-connection
When connecting or changing
the LED strip please observe the
polarity (red = plus)! Only connect
in dead-voltage condition!
LEDs are sensitive against
ESD, that means against electro-
static discharge. This can already
happen by touching connections.
Please take suitable electronic
protection measures!
5.3 Monitoring
For monitoring each luminaire
must be addressed individually.
Before fitting the covers of the
luminaires 29011 and 29021
and the trapeze shaped cover of
the luminaire 29021, the desired
address (1 - 20) is set on the
address switches by means of a
suitable screwdriver (arrowhead
to no.).
If the luminaire should not be
monitored the address „0" has
be selected on each address
switch.
5.4 Accessories
Wire guard for 29011
No. 400 71 348 370
Accessories for 29021
Chain mounting
No. 400 71 350 432
Ceiling mounting
No. 400 71 350 432
Pendulum mounting
No. 400 71 350 400, ..402, ..404
Wall bracket
No. 400 71 350 418
6. Inspection/
Maintenance/Repair
Observe the valid regulations for
the inspection, maintenance and
repair of electrical equipment!
7. Disposal/Recycling
W h e n d i s p o s i n g o f f a u l t y
equipment, observe the valid
regulations for recycling and
disposal.
Plastic parts are marked with the
appropriate symbols.
7
Werbung
Inhaltsverzeichnis
