Renkforce 1230711 Bedienungsanleitung Seite 5

• You can find the SmartBand app on the iOS app store or on Google Play by searching
for "SmartBand".
• Install the latest version of the app on your mobile device.
d) Pairing with a mobile device
The sport wristband is paired directly via the SmartBand app and not via
the Bluetooth settings on your mobile device. Check that Bluetooth
®
enabled on your mobile device. The mobile device must support Bluetooth
version 4.0.
• Open the SmartBand app.
• Tap the top-left of the control panel to open the app's main menu.
• Select "Setting".
• Scroll down until you can see the "Wrist Band Setting" menu option.
• Tap the "Wrist Band" submenu. Tap on "Pair" on the next page.
• When the app is searching for Bluetooth
button (1) on the LED unit. Let go when MENU is displayed. Wait until PAIR is
displayed and briefly press the function button. PAIR begins to blink.
• DONE is displayed when pairing has been completed successfully. PAIR will
disappear after about 20 seconds if pairing with the app was unsuccessful.
• Training data will be synced automatically as soon as the sport wristband is
connected to the SmartBand app. Bluetooth must be enabled in the mobile device
settings for this function to work. Syncing takes place automatically each time you
open the SmartBand app.
• To unpair your mobile device and the sport wristband, go to the the "Wrist Band"
submenu as described above and then tap "Unpair".
Operation
a) Turning on/off, calling up menus
• Press and hold the function button (1) to turn the wristband on. A welcome message
will be displayed.
• Press the function button and hold it down until MENU is displayed. All available
main menus will be displayed in a loop (fig. 6). Wait until the desired menu appears.
Briefly press the function button when a menu item is displayed in order to select it.
• Wait until OFF is displayed. Then press the function button to turn the wristband off.
A goodbye message will be displayed.
b) Recording and viewing training data
• Press and hold the function button (1) until MENU appears.
• Wait until WORK is displayed.
• Press the function button to start recording data. GO is displayed. You can now
begin your training program.
• Press the function button during your training to display the intermediate training
values (fig. 7).
Training progress Calories burned
• Press and hold the function button until STOP and DONE are displayed. Data
recording for your training session is stopped. REC appears. The saved data will
then be displayed automatically (fig. 8).
"Number of steps", "completed distance", "calories burned" and "training
progress" must be activated in the SmartBand app in order to view them on
the display of the LED unit.
devices, press and hold the function
®
Fig. 6
Training time Number of steps
Distance covered
is
®
®
Training progress
• You can view the data of the previous training session again at a later date. Keep
pressing the function button until REC is displayed. The data will be displayed one
after another in a loop after REC.
c) Storage
Your training data is transferred to the SmartBand app when you carry out a sync.
The LED unit stores minute-by-minute information from the last seven days and an
overview of daily training in the last 30 days.
Sync the LED unit regularly so that the SmartBand app displays as many details as
possible.
d) Selecting the display mode
• There are various display modes available for training data (fig. 9). Press the function
button to switch to the next display mode.
• When the display on the LED unit turns off, press the function button once to view
the most recent display mode.
The DAILY, STEP, DIST and CAL display modes must be enabled in the
SmartPhone app in order for them to be displayed on the LED unit.
General
information
Previous training data
General information
• In this display mode, general information is automatically displayed in a continuous
loop (fig. 11).
• MOVE shows the total duration of your training activities for each day. ACTIVE
shows the daily cumulative duration of intensive training activities (e.g. running).
• Training progress is shown with symbols which represent a percentage of the set
training goal (fig. 10).
<10 %
10 - 40 %
The MOVE and ACTIVE displays must be enabled in the SmartBand app in
order for them to be displayed on the LED unit.
Time
Fig. 7
Training time
Calories burned
Daily values
Calories burned
40 - 70 %
70 to under 100 %
Training progress Total time (movements) per day
Total time (very active time) per day
Number of steps
Distance
covered (km)
Fig. 8
Number of steps
Distance covered
Fig. 9
100 %
Fig. 10
Fig. 11