Superior KE-7951T Bedienungsanleitung Seite 17

KETTLE / GLASS TEAPOT / GLASS TEAPOT
WARMING FUNCTION
• Place the appliance on the base unit on the
socket designed for the kettle, and plug in the
mains plug. The kettle must be stable on the
socket of the base unit.
• Please ensure that the openings on the
appliance are not directed towards people
or objects as hot steam is emitted from these
openings as the water boils.
• Set the switch of the appliance to "1". The
power light indicates that the appliance is
switched on. The water will now heat up.
• Please ensure that the lid is always fully closed
while the kettle is boiling. Danger of burning.
• When the water has boiled, the appliance turns
off automatically. The switch jumps back to "0"
and the power light goes out.
• After boiling the kettle, wait a minute until the
water is no longer bubbling. Do not open the lid
while the kettle is boiling or during pouring.
• The boiling process is interrupted/ended
immediately if the kettle is lifted from the base
unit. The appliance turns off.
• The appliance is protected against over-heating,
and operation is interrupted if the appliance is
turned on unintentionally without any water. If
this happens, the appliance must be left to cool
for a minimum of 15 minutes before water is
added and the appliance can be used again.
• When the appliance is not in use, please remove
the mains plug from the socket.
GLASS TEAPOT
• The lid of the glass teapot can be opened by
pressing the button on the inside of the handle.
• Use the handle on the filter to remove this from
the teapot. You can now fill the filter with loose
tea leaves.
• Replace the filter in the teapot. The filter must be
slotted into the socket intended for it.
• Carefully pour hot water, but not boiling water,
from the kettle into the teapot.
• Close the lid of the teapot. Leave the tea to
brew.
• When the tea is ready, open the lid of the glass
teapot by pressing the button on the inside of
the handle.
• Remove the filter from the teapot. When
removing the filter, you must use the plastic
handle provided. Danger of scalding!
• Put the filter down on a surface that will not be
damaged by water or heat.
• Close the lid of the glass teapot.
• When lifting the teapot, only use the plastic
handle. Danger of burning!
WARNING:
Please note that the glass teapot is made from a
heat-resistant material, but that it is still breakable.
Never pour hot water into the pot while it is
standing on the electric base unit. In the event of a
leak, fluid could pour over the appliance. Danger
of electric shock.
Avoid subjecting the glass teapot to large
temperature differences. Never fill the teapot with
cold water when it is still hot. Check the glass
teapot regularly for any possible damage or
leaks.
GLASS TEAPOT WARMING FUNCTION
• Prepare the tea as described above in the
"Glass Teapot" section. Please note that the
warming plate is to be used only for keeping
the tea warm, and not for heating / boiling
water or tea.
• Place the full teapot on the warming plate on
the base unit.
• Press the ON/OFF button in order to switch the
warming plate on.
• The "Current Temp" light will turn on, the
display will light up, and the blue "Power" light
will appear.
• As soon as the warming plate is turned on,
the temperature sensor begins to measure the
current temperature of the tea in the glass pot.
This process can take a couple of minutes. The
display will flash while this is taking place.
• If the level of liquid in the teapot has fallen
below the minimum level, or if the teapot is not
correctly positioned on the warming plate, the
warming function will not work.
• If the temperature in the glass teapot is too
high, the warming plate will not work until the
tea has cooled sufficiently. In this case, the
blue "Power" light will only appear when the
tea has cooled sufficiently.
18 18
GB