Program Change; Pitch Bend; Channel Aftertouch - Yamaha PLG150-PF Bedienungsanleitung

1.4 Program change

This message is used to switch voices.
It changes the program number on the receiving channel. When the change is to
include the voice bank, transmit the program change after sending the Bank
Select message (see 1.2.1).
If the Multi Part parameter Rcv PROGRAM CHANGE = OFF, that part will not
receive program changes.

1.5 Pitch bend

This message conveys information on pitch bend operations.
Basically, this message is for changing the pitch of a part, but the depth of the fol-
lowing six effects can be controlled.
The effect of this message can be modified by the following parameters.
* Multi Part Parameter
1. BEND PITCH CONTROL
2. BEND FILTER CONTROL
3. BEND AMPLITUDE CONTROL
4. BEND LFO PMOD DEPTH
5. BEND LFO FMOD DEPTH
6. BEND LFO AMOD DEPTH
By default, the Pitch Control effect is applied.
If the Multi Part parameter Rcv PITCH BEND CHANGE = OFF, that part will
not receive pitch bend messages.

1.6 Channel aftertouch

This message conveys the pressure after the key is played on the keyboard (for an
entire MIDI channel). The pressure can be controlled for each part. This message
will affect the notes currently playing.
The effect of this message can be modified by the following parameters.
* Multi Part Parameter
1. CAT PITCH CONTROL
2. CAT FILTER CONTROL
3. CAT AMPLITUDE CONTROL
4. CAT LFO PMOD DEPTH
5. CAT LFO FMOD DEPTH
6. CAT LFO AMOD DEPTH
By default, there will be no effect.
If the Multi Part parameter Rcv CHANNEL AFTER TOUCH = OFF, that part
will not receive Channel Aftertouch.
1.7 Polyphonic aftertouch
This message conveys the pressure after the key is played on the keyboard (for
individual note number). The pressure can be controlled for each part. This mes-
sage will affect the notes currently playing.
The effect of this message is determined by the following Multi Part parameters.
1. PAT PITCH CONTROL
2. PAT AMPLITUDE CONTROL
3. PAT LFO PMOD DEPTH
4. PAT LFO FMOD DEPTH
5. PAT LFO AMOD DEPTH
By default, there will be no effect.
If the Multi Part parameter Rcv CHANNEL AFTER TOUCH = OFF, that part
will not receive Polyphonic Aftertouch.
2. System exclusive messages
2.1 Parameter changes
This device uses the following parameter changes.
[ UNIVERSAL REALTIME MESSAGE ]
1) Master Volume
[ UNIVERSAL NON REALTIME MESSAGE ]
1) General MIDI System On
[ XG PARAMETER CHANGE]
1) XG System on
2) XG System parameter change
3) Multi Part parameter change
[ PLG150-PF NATIVE PARAMETER CHANGE ]
1) PLG150-PF System parameter change
2) PLG150-PF Part parameter change
2.1.1 Universal realtime messages
2.1.1.1 Master Volume
11110000 F0H
7FH
01111111
7FH
01111111
00000100 04H
01H
00000001
* 0sssssss SSH
TTH
0ttttttt
11110111 F7H
or
F0H
11110000
01111111 7FH
XNH
0xxxnnnn
00000100 04H
01H
00000001
0sssssss SSH
TTH
0ttttttt
F7H
11110111
When received, the Volume MSB is reflected in the System Parameter MAS-
TER VOLUME.
* The binary expression 0sssssss is expressed in hexadecimal as SSH.
The same applies elsewhere.
2.1.2 Universal non-realtime messages
2.1.2.1 General MIDI System On
F0H
11110000
7EH
01111110
01111111 7FH
09H
00001001
00000001 01H
F7H
11110111
or
F0H
11110000
7EH
01111110
0xxxnnnn XNH
09H
00001001
00000001 01H
F7H
11110111
When this message is received, the SOUND MODULE MODE is set to XG,
and all data except for MIDI Master Tuning will be restored to the default
value.
However this message will not be received when SOUND MODULE MODE
= C/M.
Since approximately 50ms is required to process this message, be sure to
allow an appropriate interval before sending the next message.
2.1.3 XG Parameter Change
This message sets XG-related parameters. Each message can set a single
parameter.
The message format is as follows.
F0H
11110000
43H
01000011
1NH
0001nnnn
01001100 4CH
GGH
0ggggggg
0mmmmmmm MMH
LLH
0lllllll
VVH
0vvvvvvv
: :
F7H
11110111
For parameters whose Data Size is 2 or 4, the appropriate amount of data will
be transmitted as indicated by Size.
MIDI Data Format
= Exclusive status
= Universal Real Time
= ID of target device
= Sub-ID #1=Device Control Message
= Sub-ID #2=Master Volume
= Volume LSB
= Volume MSB
= End of Exclusive
= Exclusive status
= Universal Real Time
= Device Number, xxx = don't care
= Sub-ID #1=Device Control Message
= Sub-ID #2=Master Volume
= Volume LSB
= Volume MSB
= End of Exclusive
= Exclusive status
= Universal Non-Real Time
= ID of target device
= Sub-ID #1=General MIDI Message
= Sub-ID #2=General MIDI On
= End of Exclusive
= Exclusive status
= Universal Non-Real Time
= N:Device Number, X:don't care
= Sub-ID #1=General MIDI Message
= Sub-ID #2=General MIDI On
= End of Exclusive
Exclusive status
YAMAHA ID
N:device Number
Model ID
Address High
Address Mid
Address Low
Data
End of Exclusive
37