Werbung
Verfügbare Sprachen
Verfügbare Sprachen
S S e e t t s s w w i i t t c c h h i i n n g g o o n n h h y y s s t t e e r r e e s s i i s s ∆ ∆ a a f f o o r r a a l l a a r r m m 1 1
Menu <–> Selection
Example 1.0
Select digit
Set digit
press the
key to accept the selection
S S e e t t s s w w i i t t c c h h i i n n g g o o f f f f h h y y s s t t e e r r e e s s i i s s ∆ ∆ b b f f o o r r l l i i m m i i t t 1 1
Menu <–> Selection
Example: 1,0
Select digit
Set digit, then select signal form for output 1,
Chapter 5.5.1.6
press the
keey to accept the selection
5 5 . . 5 5 . . 1 1 . . 5 5 R R e e s s e e t t L L a a t t c c h h s s i i g g n n a a l l a a t t o o u u t t p p u u t t 1 1
Menu <–> Selection
Manual reset with red key
Alarm output can only be reset manually if
is selected as the function and is displayed. If
lected as the function and is displayed, then the alarm output can only be
reset manually if the totalizer reset parameter
grammed as
Electrical reset with MPI-Input
Alarm output can only be reset electrically, if
is selected as the function and is displayed.
If
is selected as the function and is displayed, then the alarm out-
put can only be reset electrically if the totalizer reset parameter
has been programmed as
N N o o t t e e : : The Display Hold funktion is off.
Both manual and electrical reset
Alarm output can either be reset manually via the red key or via a reset pulse
on the MP input. If
then the alarm output can only be reset manually and/or electrically if the to-
talizer reset parameter
press the
key
N N o o t t e e : : The Display Hold function is off.
to accept
Page 22
23
or
,
has been pro-
or
.
,
.
is selected as the function and is displayed,
is programmed as
.
5 5 . . 5 5 . . 1 1 . . 6 6 S S e e l l e e c c t t S S i i g g n n a a l l F F o o r r m m f f o o r r O O u u t t p p u u t t 1 1 ( ( B B r r e e a a k k c c o o n n t t a a c c t t / / M M a a k k e e c c o o n n t t a a c c t t ) )
Menu <–> Selection
press the
key
to accept
5 5 . . 5 5 . . 2 2 A A l l a a r r m m 2 2 / / A A l l a a r r m m o o u u t t p p u u t t 2 2
5 5 . . 5 5 . . 2 2 . . 1 1 A A l l a a r r m m 2 2 o o n n / / o o f f f f
Menu <–> Selection
5 5 . . 5 5 . . 2 2 . . 2 2 A A s s s s i i g g n n A A l l a a r r m m 2 2
is se-
Menu <–> Selection
or
a
5 5 . . 5 5 . . 2 2 . . 3 3 M M o o d d e e f f o o r r A A l l a a r r m m o o u u t t p p u u t t 2 2 (for function, see graphic on page 20)
Menu <–> Selection
press the
key to accept the selection
Make contact function
Work contact is made (clamp 4 to 5) when measured
value is > limit value 1
Break contact function
Work contact is broken (clamp 4 to 5) when measured
value is > limit value 1
Example: on
Alarm 2 not activated,
Chapter 5.6,
Alarm 2 not activated, press the
key to accept the selection
Limit value can be either assigned to the
Example: on
totalizer value or to the current measured
value.
Totalizer
instantaneous value, press the
key to accept the selection
Example: on
Reset Latch mode, Latch signal at output 2
Chapter 5.5.2.5 ,
24
Auto mode
25
Page 23
Werbung
