Saw Blades - DeWalt DWE396 Originalanweisungen

3. With the hex key , loosen both of the blade setting screws
7
13 . The screws will be held in place by the screw clips.
4. Carefully pull the saw-blade-end up until it is disengaged
from and clear of the Blade-Clamp-system.
5. Pull the saw blade back and out of the front guard
take it off of the bar 6 .
6. Repeat this procedure for the other saw blade.
Fitting the saw blades (Fig. D)
1. Slide one saw-blade into the blade guide slot
sure that the end with the slotted hole
guard 14 .
2. Slide the back of the saw blade down until the threaded
hole aligns with the blade setting screw
15
3. Repeat this procedure for the other saw blade.
4. Tighten both saw blade setting screws
pressing and turning simultaneously with the short end of
the hex key .
7
5. Close the gearcase cap 12
cap screw.

WARNING: Before operation let the saw blades run freely
for approx. 20 s.

Saw Blades

Cat. No. Material to be cut
DWE396 Rough wood
Fine wood
Fine wood
Low density building block
Medium density building block
DWE397 Rough wood
Low density building block
Medium density building block
Insulation materials
Celluar contrete
DWE398 Rough wood
Low density building block
Medium density building block
Insulation materials
Celluar contrete
DWE399 Rough wood
Low density building block
Medium density building block
Insulation materials
Celluar contrete
Prior to Operation (Fig. A)
• Mount the appropriate type of saw blade.
• Check that the tool is running properly and can perform all
its functions. Make sure that the bar
the saw blades 5 and the housing are undamaged.
and
14
making
9
16 fits into the front
.
13
13 securely by
and tighten the gearcase
Recommended saw
blade type
HSS DT2970
HSS DT2971
TCT DT2972
TCT T12 DT2973
TCT T20 DT2977
HSS DT2978
TCT T12 DT2974
TCT T20 DT2976
HSS DT2979
TCT 12 DT2975
HSS DT2978
TCT T12 DT2974
TCT T20 DT2976
HSS DT2979
TCT 12 DT2975
HSS DT2978
TCT T12 DT2974
TCT T20 DT2976
HSS DT2979
TCT 12 DT2975
6 is still straight and
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.

WARNING:
• Ensure the material to be sawn is secured in place.
• Apply only a gentle pressure to the tool and do not
exert side pressure on the saw blade.
• Avoid overloading.

WARNING: For applications where mineral dust or
hardwood is emitted due to the work process the machine
shall be connected to a suitable dust extraction system.
Proper Hand Position (Fig. A, F)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the front handle
with the other hand on the rear grip handle
Switching On and Off (Fig. A)
For safety reasons the ON/OFF switch
lock-off button 2 .
1. Push the lock-off button 2
2. To run the tool, press the ON/OFF switch
as the ON/OFF switch is released the lock-off switch is
automatically activated to prevent unintended starting.
3. Always switch off the tool before unplugging.
Sawing (Fig. A, C, D, F)
NOTICE: Do not use the saw for cutting curves or pockets.
Make sure the bar end protrudes from the workpiece.
For long, straight cuts first draw a line on the workpiece and
follow the line.
Make downward cuts only. Avoid cutting earth as this will blunt
the saw blades very quickly.
When using a saw horse always cut on the outside of the saw
horse arms.
1. Clamp the workpiece on one side only to prevent the bar
from jamming in the workpiece. Should this happen, ease
open the cut with wedges to relieve the strain on the blade.
Do not try to wrench the saw free.
2. Hold your D WALT power tool by the front handle
e
the rear grip handle to guide the saw properly.
3
EngLIsh
4
3 .
is equipped with a
1
to unlock the tool.
.As soon
1
and
4
21