Aux In Socket; Cleaning And Maintenance; Technical Data - AEG MC 4462 BT Bedienungsanleitung

The device stops automatically after all programmed titles
have been played. The programmed sequence will remain in
the memory until you switch to a different operating mode.
Playing back Music in MP3 Format
With this device it is possible to play back pieces of music in
MP3 format. The device also supports all standard CD types:
CD, CD-RW, CD-R.
This machine of is able to play MP3 CDs. Up to 200 tracks
can be compressed and stored on these CDs. Your machine
detects an MP3 CD automatically (the total number of tracks
and MP3s appears in the display). If you would like to play
one of these CDs, proceed as described under "Playing
CDs/MP3". Tracks can be programmed as described under
"Playing Back Programmed Tracks".
Please note:
There are a number of different recording and compression
methods, as well as quality differences between CDs and self-
recorded CDs.
Furthermore, the music industry does not adhere to fixed
standards (copy protection).
For these reasons it is possible that in rare cases there are
problems with the playback of CDs and MP3 CDs. This is not
a malfunction of the device.

AUX IN socket

To connect analogue replay devices. Via this socket you can
also hear the sound of other playback devices such as MP3
players, CD players etc. through the loudspeakers.
1. Please connect the external device with a 3.5 mm stereo
jack plug to the AUX-IN socket.
2. Repeatedly press the FUNCTION button (18), until "AUX"
is shown in the display.
3. You will hear the sound playback from the external device
through the loudspeakers. You may use the VOLUME
control (12) to adjust the volume. The CD buttons are not
functional.
4. For the remaining procedure please see the operating
instructions of the external sound source.
NOTE:
Adjust the volume of the external device to a comfortable
level.

Cleaning and Maintenance

WARNING:
Do not immerse the device in water.
• Always remove the mains plug before cleaning the
machine.
• Any marks on the surface can be wiped off with a slightly
damp cloth without any additives.
Troubleshooting
Symptoms Course
CD can not be CD is not inserted
played back. or inserted incor-
rectly.
CD jumps dur- Check the disc for
ing playback. fingerprints, dirt or
scratches.
Device cannot Device crashes and
be operated. "hangs".
No audio The device is not
signal during registered with the
bluetooth con- audio source.
nection.
Volume too low.
Device can not Registration does
be connected. not work.
Audio source is
shut off.
Bluetooth is shut
off on the audio
source.
Bluetooth version
is not supported.

Technical Data

Model: ........................................................................... MC 4462 BT
Power supply: ...................................................100 - 240 V~, 50 Hz
Power consumption:.................................................................65 W
Protection class: ................................................................................II
Net weight: ..............................................................approx. 9.34 kg
Radio section:
Frequency ranges: ...............................FM 87.5 ~ 108.0 MHz
Bluetooth
Bluetooth support: ........................................................V3.0 + EDR
Range: ..................................................................approx. 15 metres
Transmission frequency: ......................................2.402-2.480 GHz
Protocols: ....................................................................A2DP/AVRCP
The right to make technical and design modifications in
the course of continuous product development remains
reserved.
English
45
Solution
Ensure that the disc is
inserted with the label
facing upwards.
Check the disc for
fingerprints, dirt or
scratches.
Disconnect the power
supply for 5 sec. Then
switch the device on
again.
Ensure that there is a
connection. Register
the device with the
audio source again, if
necessary.
Increase the volume
on the device.
Increase the volume
on the audio source.
Check to see if the
audio source supports
the A2DP protocol.
Turn on the audio
source.
Turn on the Bluetooth
function on the audio
source.
Use a different play-
back device.