5. ENDLAGEN ZURÜCKSETZEN
5.1 Obere Endlage zurücksetzen
5.1.1 Stellen Sie sicher, dass kein Kanal auf der Fernbedienung ausgewählt ist.
Achtung:
5.1.2 und 5.1.3 müssen innerhalb von drei Sekunden durchgeführt werden !
5.1.2 Halten Sie die Motortaste gedrückt
5.1.3 Drücken Sie die OPEN-Taste.
5.1.4 Lassen Sie die Motortaste los.
Die obere Endlage ist jetzt gelöscht.
5.2 Untere Endlage zurücksetzen
5.2.1 Stellen Sie sicher, dass kein Kanal auf der Fernbedienung ausgewählt ist.
Achtung:
5.2.2 und 5.2.3 müssen innerhalb von drei Sekunden durchgeführt werden !
5.2.2 Halten Sie die Motortaste gedrückt
5.2.3 Drücken Sie die CLOSE-Taste.
5.2.4 Lassen Sie die Motortaste los.
Die untere Endlage ist jetzt gelöscht.
70
5.1 Clear top limit
5.1.3
5. Clearing end limits
5.1 Clear top limit
5.1.1
5.1.2
5.1.1
Deselect all Group number on the remote
5.1.4
5.1.3
Press the open button.
Note
To re-position the bottom limit of the blind, clear the bottom limit and repeat step
limit (bottom)
IMPORTANT
Watch out to perform steps 6.1.2 and 6.1.3 within 3 seconds!
5.1.3
5. Clearing end limits
5.2.2
Press and hold the manual control button
5.1 Clear top limit
.
5.1.2
Press and hold the manual control button
5.1.2
5.1.4
Release the manual control button .
.
5.2 Clear bottom limit
5.1.1
Deselect all Group number on the remote
Page 13 of 18
5.2.1
5.1.4
5.2.3
Press the close button.
IMPORTANT
5.2 Clear bottom limit
Watch out to perform steps 6.1.2 and 6.1.3 within 3 seconds!
5.2.1
Deselect all Group number on the remote
Page 13 of 18
5.1.2
Press and hold the manual control button
.
5.2 Clear bottom limit
5.2.4
Release the manual control button .
Page 13 of 18
Press the open button.
Deselect all Group number on the remote
Press and hold the manual control button
.
Release the manual control button .
IMPORTANT
Watch out to perform steps 6.1.2 and 6.1.3 within 3 seconds!
Press the open button.
The blind will jog 2x to indicate the top limit is
Die Anlage wird sich zweimal
cleared
kurz auf und ab bewegen, um
anzuzeigen, dass die Endlage
zurückgesetzt wurde.
Press and hold the manual control button
.
Deselect all Group number on the remote
Release the manual control button .
Die Anlage wird sich zweimal kurz auf
IMPORTANT
und ab bewegen, um anzuzeigen, dass
die Endlage zurückgesetzt wurde.
Watch out to perform steps 6.2.2 and 6.2.3 within 3 seconds!
5.1.1
The blind will jog 2x to indicate the top limit is
cleared
5.1.3
4.2. Close
5.2.1
The blind will jog 2x to indicate the top limit is
cleared
5.2.3
The blind will jog 2x to indicate the bottom limit is
cleared
5.1.2
5.1.4
5.2.2
5.2.4