Cleaning & Maintenance - Bosch sensixx B45L Gebrauchsanleitung

4. Lean the appliance on the opposite side of the
ilter opening.
5. Unscrew the ilter (12) and take it out.
6. To wash the ilter, you may:
a. Place the ilter under the water tap and wash
it up until calc residues are removed. Squeeze
the ilter as indicated in the picture F.
b. Immerse the ilter in tap water (250 ml) mixed
with a measure (25 ml) of descaling luid.
The descaling luid can be obtained from our
Aftersales Service or Specialist outlets:
Accessory code
(After-sales)
311144
7. Holding your steam generator in the lateral position
and using a jug, ill the boiler with 1/4 litre of water
and replace the ilter.
8. Shake the base unit for a few moments, unscrew
the ilter again and empty the boiler completely
over a sink or bucket.
For best results, we recommend that this operation
is performed twice.
Important: before re-closing, make sure no water
remains in the boiler.
9. Replace and tighten up the ilter.
To reset the "Clean" counter, switch the station
off twice, keeping it off for at least 30 seconds
each time.
(on → 30s off → on → 30s off → on)
Rinsing the iron steam chamber (G)
Caution! Risk of burns!
This procedure helps to remove scale particles from
the steam chamber.
Perform approximately every 2 weeks, if the water in
your area is very hard.
a) Ensure that the iron has cooled down.
b) Set the temperature to the
c) Fill the tank with tap water.
d) Plug in the mains cable and set the main power
button (9) to the "I" position, (illuminated in red).
e) Set the steam setting to
stops lashing.
f) Hold the iron over the sink or a container to collect
the water.
g) Press the steam release button (13) and gently
shake the iron. Boiling water and steam will be
released, carrying scale and or deposits that
might be inside. This could take approximately 5
minutes.
Name of accessory
(Specialist outlets)
TDZ1101
setting.
and wait until the icon
h) Set the temperature to the
pressing the steam release buttons (13-14*).
The water in the steam chamber will start evaporating.
Wait until all the water inside the chamber has
been evaporated.
i) To clean the soleplate, immediately rub off any
residue by running the hot iron over dry cotton
cloth.
Recommended accessory
The B45L steam station produces a high amount of
steam for best performance.
Therefore, the best additional accessory would be
the Bosch active-ironing board TDN1010.
Cleaning & Maintenance
Attention! Risk of burns!
Always unplug the appliance from the mains
supply before carrying out any cleaning or
maintenance operation on it.
1. After ironing, disconnect the plug and allow the
appliance to cool down before cleaning.
2. Wipe the housing, handle and iron body with a
damp cotton cloth.
3. If the soleplate is soiled with dirt or scale, clean it
with a damp cotton cloth.
4. Never use abrasive products or solvents.
Storing the appliance (H)
1. Always allow the appliance to cool down before
storing it.
2. Set the main power button to the "0" position (the red
light will go off) and disconnect the mains cable.
3. Place the iron on the iron pad (2), standing on the
soleplate, and ix it by inserting the tip of the iron
into the front slot and moving the ixation system
lever (10) against the heel of the iron.
4. Store the mains cable (5) and steam hose (6) in
the storage compartment (4). Do not wrap the
cords too tight.
5. Hold the iron´s handle when moving the appliance,
as shown in igure H, or use the carrying handles
(3) on the sides.
setting, without